leica gs15 user manual

leica gs15 user manual

Allow USB connect Page 33 and 34: Accessing theWeb server viaBluetoot Page 35 and 36: StepThisDescriptionprocedure has to Page 37 and 38: Switching to areal-time baseFunctio Page 39 and 40: 3.2 Batteries3.2.1 Operating Princi Page 41 and 42: StepDescription4. Close the cover o Page 43 and 44: StepDescription3. With the battery Page 45 and 46: StepTheDescriptionSD card is insert Page 47 and 48: StepDescription4. Do not force the Page 49 and 50: Attach and detacha clip-on-housings Page 51 and 52: Insert and removea SIM cardstep-by- Page 53 and 54: LED indicatorsDescriptionEach clip- Page 55 and 56: IF the on is THENGFU24 with redcall Page 57 and 58: 3.4.2 GS15Devices fitting intothe G Page 59 and 60: Step Description5. Page 151 and 152: GGAT 1, antenna. Page 153 and 154: OOperating timesGS10. Page 155 and 156: StatusGS10.Thank you, for helping us keep this platform clean. The editors will have a look at it as soon as possible. Read carefully through the User Manual before you switch on the product. Product identification The type and serial number of your product are indicated on the type plate. Enter the type and serial number in your manual and always refer to this information when you need to contact your agency or Leica Geosystems authorised service workshop. Type: Serial No.: Indicates a potentially hazardous situation or an unintended use which, if not avoided, could result in death or serious injury. Important paragraphs which must be adhered to in practice as they enable the product to be used in a technically correct and efficient manner. Trademarks Windows is a registered trademark of Microsoft Corporation in the United States and other countries Bluetooth is a registered trademark of Bluetooth SIG, Inc. SD is a trademark of the SD Card Association All other trademarks are the property of their respective owners. Intended as a quick reference guide. All instructions required in order to operate the product - to a basic level are contained in the User Manual.http://ganteltechnology.com/system/userfiles/colchester-triumph-2000-owners-manual.xml

• leica gs15 user manual, leica viva gs15 user manual, leica gs15 user manual, leica cs15 user manual, leica gs15 user manual user, leica gs15 user manual instructions, leica gs15 user manual pdf, leica gs15 user manual instruction, leica gs15 user manual.

Provides an overview of the product together with technical data and safety directions. Intended as a quick reference field guide. Describes the general working of the product in - standard use. Intended as a quick reference field guide. With direct access to myworld, you are able to access all relevant services whenever it is convenient for you, 24 hours a day, 7 days per week. View detailed information on your products, buy additional options or Customer Care Packages (CCPs), update your products with the latest software and keep up-to-date with the latest documentation. View the service history of your products in Leica Geosystems Service Centers and detailed information on the services performed on your products. For your products that are currently in Leica Geosystems Service Centers view the current service status and the expected end date of service. Create new support requests for your products that will be answered by your local Leica Geosystems Support Team. View the complete history of your Support and view detailed information on each request in case you want to refer to previous support requests. Enhance your product knowledge with the Leica Geosystems Campus - Information, Knowledge, Training. Study the latest online training material or download training material on your products. Keep up-to-date with the latest News on your products and register for Seminars or Courses in your country. 6 Web-based tool to preprogram the GNSS instrument. To receive the satellite signals from the GNSS satellites. The office software including a series of help programs which support working with Leica Viva Series instruments. Instruments Depending on the satellite systems and signals configured, a maximum number of 120 channels is allocated. The GS GNSS instruments are additionally designed to support Compass. The Compass signal definition is not fully finalised, although, test signals have been tracked in a test environment.http://eaupureinternational.com/userfiles/advent-modena-m201-service-manual.xml

As changes can still occur, Leica Geosystems cannot guarantee full Compass compatibility. The Web server application is integrated into the firmware and cannot be deleted. The English language is integrated into the firmware and cannot be deleted. Numerous languages are available for the Web server application. The English language is the default language. One language is chosen as the active language. Ensure that the battery is at least 75% full before beginning the upload, and do not remove the battery during the upload process. 14 Software for All GS models Description The software can be uploaded using the Leica Web server application or Geosystems. Ensure that a Leica SD card is inserted into the GS instrument before starting the upload.Power for the instrument can be supplied either internally or externally. Up to two external power supplies can be connected. Internal power supply: Two batteries (for GS10: GEB221 or GEB222; for GS15: GEB211 or GEB212) fit into the instrument. External power supply: GEB171 battery connected via a cable.SD card: All GS GNSS instruments have an SD card slot fitted as standard. An SD card can be inserted and removed. Available capacity: 1 GB. While other SD cards can be used, Leica Geosystems recommends to only use Leica SD cards and is not responsible for data loss or any other error that can occur while using a non-leica card. Unplugging connecting cables or removing the SD card during the measurement can cause loss of data. Only remove the SD card or unplug connecting cables when the GS GNSS instrument is switched off. SD cards can directly be used in an OMNI drive as supplied by Leica Geosystems. Other PC card drives can require an adaptor.The Position LED flashes red quickly three times. Press and hold buttons for 5 s. The Memory LED flashes red quickly three times. The SD card of the GNSS instrument is formatted. The Memory LED continues to flash red as the SD card is formatted. Press and hold buttons for 10 s.

25 Button Function The System RAM on the GNSS instrument is formatted. Settings of all installed software will be deleted. All LEDs (except Battery LED and Bluetooth LED) flash red quickly three times. After the formatting the System RAM, the GNSS instrument is turned off. Press and hold buttons for 15 s. The registry of the GNSS instrument is deleted. Windows CE and communication settings will be reset to factory defaults. All LEDs (except Battery LED and Bluetooth LED) flash red quickly three times. After deleting the registry, the GNSS instrument is turned off. Microsoft Active- Sync or Windows Mobile Device Center enables a PC and a Windows mobile-based pocket PC to communicate. Install Leica Viva USB drivers Step Description 1. Start the PC. 2. Insert the Leica Viva Series DVD. For PCs with Windows Vista or Windows 7 operating system: If not already installed, Windows Mobile Device Center will be installed additionally. 8. The InstallShield Wizard Completed window appears. 29 Step Description 9. Check I have read the instructions and click Finish to exit the wizard. Run the ActiveSync installation program if not already installed. 13. Allow USB connections inside the Connection Settings window of Active- Sync. For PCs with Windows Vista or Windows 7 operating system: 14. Windows Mobile Device Center starts up automatically. For PCs with Windows XP operating system: ActiveSync starts up automatically. If does not start automatically, start ActiveSync. If not already installed, run the ActiveSync installation program. The folders on the CS field controller are displayed under Mobile Devices. The folders of the data storage device can be found in StorageCard. For PCs with Windows Vista or Windows 7 operating system: Windows Mobile Device Center starts up automatically. If does not start automatically, start Windows Mobile Device Center. 33 3.1.

2 Connecting to the Web Server Description Accessing the Web server via cable step-by-step The Web server is a web-based tool to view the status of and configure the GNSS instruments. The Web server application is integrated into the GS firmware and cannot be deleted. Step Description 1. Start the PC and turn on the GS GNSS instrument. Instead of connecting to your PC, you can connect your GS GNSS instrument to the Leica CS field controller. 2. Connect the GS GNSS instrument with the GEV234 cable to the PC. The GS GNSS network adapter is configured with IP address: A DOS window appears when the configuration was successful. Press any key to exit the DOS window. The Configure GS connection shortcut disappears from the desktop. 4. Start the web browser of your PC. 5. Type in and press enter to access the web server of GS instrument. This procedure has to be done only once. 35 Establishing a Bluetooth connection between PC and GS GNSS instrument Step Description 1. Start the PC and turn on the GS GNSS instrument. Instead of connecting to your PC, you can connect your GS GNSS instrument to the Leica CS field controller. In this case, turn on the Leica CS field controller, start SmartWorx Viva and establish a Bluetooth connection to the GS GNSS instrument. 2. Run the Bluetooth software and start the Bluetooth Setup Wizard. 3. Click Next. The Bluetooth Device Selection will be started and an automatic search will be done. 4. Select the shown GS GNSS instrument and click Next. The Bluetooth Security Setup is started. 5. Type in 0000 as Bluetooth security code and click Pair Now. The pairing procedure will be done and the Bluetooth Service Selection is started. 6. Highlight Personal Ad-hoc Network and check the checkbox for Personal Ad-hoc Network. Do not select Serial Port as service. 7. Click Next. The Bluetooth Setup Wizard Completion Page is started. 8. Type in a name for your GS GNSS instrument and click Finish to complete the Bluetooth Setup Wizard.

You will see the home functions following: Go to Work. To select and start the Wake-up application. Current Status To access GNSS information of the GS as well as the instrument firmware. Instrument To access configuration settings for the GS. User To upload and activate firmware, licence keys and languages. 37 3.1.3 Configuring the Instrument Description The instrument can be set up as real-time rover or as real-time base by pressing the function button. Turn on the instrument before pressing the function button. The RTK base LED flashes yellow for 2 s. in rover mode No action. The GS has to be switched to base mode first. It is normal for the battery to become warm during charging. Using the chargers recommended by Leica Geosystems, it is not possible to charge the battery if the temperature is too high. For Li-Ion batteries, a single discharging and charging cycle is sufficient. We recommend carrying out the process when the battery capacity indicated on the charger or on a Leica Geosystems product deviates significantly from the actual battery capacity available. This releases the battery from its fixed position. 8. Pull out the battery. 9. Close the cover of the battery compartment and tighten the screw. 10. Repeat steps 6. to 9. for the second battery compartment. This releases the battery from its fixed position. 9. Remove the battery. 10. Insert the cover into the battery compartment and push the slide fastener in the direction of the arrow with the close-lock symbol. 11. Repeat steps 7. to 10. for the second battery compartment. Use it only within the specified temperature range. Do not bend the card. Protect the card from direct impacts. The card should be held with the contacts upwards and facing the slot. 5. To remove the card, push the slide fastener of battery compartment 1 in the direction of the arrow with the open-lock symbol and remove the cover. 6. Gently press on the top of the card to release it from the slot. 7. Remove the SD card. 8.

Insert the cover into battery compartment 1 and push the slide fastener in the direction of the arrow with the close-lock symbol. LED indicators Description Each clip-on-housing for a radio or digital cellular phones has Light Emitting Diode indicators on the bottom side.Signal strength LED red device is on, not registered on the network. GFU19 (US), GFU25 (CAN) with CDMA Multi- Tech MTMMC-C flashing red off device is on, registered on the network.Siemens MC75, red: long flash, no SIM card inserted, no PIN GFU28 with Telit long break entered or network search, user UC864-G authentication or network login in progress.GPRS PDP context activated. Packet switched data transfer is in progress.Power LED any device off power is off. For the equipment setup as real-time base station with radio, it's recommended to use an external radio antenna mounted on a second tripod. This increases the height of the radio antenna and therefore maximises radio coverage. Refer to the Leica Viva GNSS Getting Started Guide for detailed information about the setup. LED indicators Description Each slot-in-device for a radio or digital cellular phones has Light Emitting Diode indicators on the bottom side. M3-TR1 Data any device off data is not being transferred.GPRS PDP context activated. Packet switched data transfer is in progress.They indicate the basic instrument status.The remaining time for which enough power is available depends on the type of survey, the temperature and the age of the battery.LED is green for 1 s every 10 s. power is 20% - 40%. LED is yellow for 1 s every 10 s. power is less than 20%. No RTK data is being received at the interface of the communication device. RTK data is being received at the interface of the communication device. Set up the instrument in locations which are free of obstructions such as trees, buildings or mountains. For static surveys, the antenna must be kept perfectly steady throughout the whole occupation of a point.

Place the antenna on a tripod or pillar. Centre and level the antenna precisely over the marker. Never carry the product loose in a road vehicle, as it can be affected by shock and vibration. Always carry the product in its transport container and secure it. When transporting the product by rail, air or sea, always use the complete original Leica Geosystems packaging, transport container and cardboard box, or its equivalent, to protect against shock and vibration. When transporting or shipping batteries, the person in charge of the product must ensure that the applicable national and international rules and regulations are observed. Before transportation or shipping, contact your local passenger or freight transport company. 71 4.2 Storage Product Respect the temperature limits when storing the equipment, particularly in summer if the equipment is inside a vehicle. At the recommended storage temperature range, batteries containing a 10% to 50% charge can be stored for up to one year. After this storage period the batteries must be recharged. Remove batteries from the product and the charger before storing. After storage recharge batteries before using. Protect batteries from damp and wetness. Wet or damp batteries must be dried before storing or use. If necessary, moisten the cloth with water or pure alcohol. Do not use other liquids; these may attack the polymer components. Do not repack until everything is dry. Always close the transport container when using in the field. Cables and plugs Connectors with dust caps Keep plugs clean and dry. Blow away any dirt lodged in the plugs of the connecting cables. Wet connectors must be dry before attaching the dust cap. 73 5 Safety Directions 5.1 General Introduction Description The following directions enable the person responsible for the product, and the person who actually uses the equipment, to anticipate and avoid operational hazards.

The person responsible for the product must ensure that all users understand these directions and adhere to them. Carrying out measurement tasks using various GNSS measuring techniques. Recording GNSS and point related data. Data communication with external appliances. Measuring raw data and computing coordinates using carrier phase and code signal from GNSS satellites. 75 Adverse use Use of the product without instruction. Use outside of the intended limits. Disabling safety systems. Removal of hazard notices. Opening the product using tools, for example screwdriver, unless this is permitted for certain functions. Modification or conversion of the product. Use after misappropriation. Use of products with recognisable damages or defects. Use with accessories from other manufacturers without the prior explicit approval of Leica Geosystems. Inadequate safeguards at the working site, for example when measuring on roads. Controlling of machines, moving objects or similar monitoring application without additional control- and safety installations. WARNING Adverse use can lead to injury, malfunction and damage. It is the task of the person responsible for the equipment to inform the user about hazards and how to counteract them. The product is not to be operated until the user has been instructed on how to work with it. Local safety authorities and safety experts must be contacted before working in hazardous areas, or close to electrical installations or similar situations by the person in charge of the product. 77 5.4 Responsibilities Manufacturer of the product Manufacturers of non Leica Geosystems accessories Person in charge of the product Leica Geosystems AG, CH-9435 Heerbrugg, hereinafter referred to as Leica Geosystems, is responsible for supplying the product, including the user manual and original accessories, in a safe condition.

The manufacturers of non Leica Geosystems accessories for the product are responsible for developing, implementing and communicating safety concepts for their products, and are also responsible for the effectiveness of those safety concepts in combination with the Leica Geosystems product. The person in charge of the product has the following duties: To understand the safety instructions on the product and the instructions in the user manual. To be familiar with local regulations relating to safety and accident prevention. To inform Leica Geosystems immediately if the product and the application becomes unsafe. To ensure that the national laws, regulations and conditions for the operation of radio transmitters are respected. This person is also accountable for the training and the deployment of personnel who use the product and for the safety of the equipment in use. 79 5.5 Hazards of Use WARNING CAUTION DANGER The absence of instruction, or the inadequate imparting of instruction, can lead to incorrect or adverse use, and can cause accidents with far-reaching human, material, financial and environmental consequences. Precautions: All users must follow the safety directions given by the manufacturer and the directions of the person responsible for the product. Watch out for erroneous measurement results if the product has been dropped or has been misused, modified, stored for long periods or transported. Precautions: Periodically carry out test measurements and perform the field adjustments indicated in the user manual, particularly after the product has been subjected to abnormal use and before and after important measurements. Because of the risk of electrocution, it is dangerous to use poles and extensions in the vicinity of electrical installations such as power cables or electrical railways. If it is essential to work in this environment, first contact the safety authorities responsible for the electrical installations and follow their instructions.

WARNING WARNING During dynamic applications, for example stakeout procedures there is a danger of accidents occurring if the user does not pay attention to the environmental conditions around, for example obstacles, excavations or traffic. Precautions: The person responsible for the product must make all users fully aware of the existing dangers. Inadequate securing of the working site can lead to dangerous situations, for example in traffic, on building sites, and at industrial installations. Precautions: Always ensure that the working site is adequately secured. Adhere to the regulations governing safety and accident prevention and road traffic. View more This manual contains important safety directions as well as instructions for setting up This manual contains important safety directions as well as instructions EDGE Models RF825-E, RF825-E-AP CDMA Models RF825-C-Nx, RF825-C-Nx-AP Quick Start Guide This guide will help you get connected as quickly and This little gadget This manual contains important safety and operating information in order to prevent accidents. Please read this manual thoroughly These limits are designed Models: MAX-306M1 (2.5 GHz) and MAX-316M1 (3.5 GHz) Product The is a laser tool for general construction and other leveling applications. It is This manual contains important safety directions as well as instructions This user manual Cisco Small Business After installing your device, locate the serial WMP300N (EU) Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of This two-in-one Turbo Stick with memory storage User Guide WIRELESS WMP54GR. Model No. WMP54GR Copyright and Trademarks Specifications are subject to change without notice. This guide will help you get connected as quickly and Welcome to HUAWEI This quick start guide will help you become familiar with our DVR in a very short time.

Before installation and How to connect your D200 using GPRS (SIM Card) This User Guide provides step by step instructions that will take you through Model F2D USER MANUAL Dual-Bay RAID Storage Enclosure for two 3.5-inch Serial ATA Hard Drives. User Manual March 31, 2014 v1.2 www.akitio. Other marks are trademarks of their respective owners. Table of Contents Table Cisco Small Business Clarinet Systems, Inc. Page 1 Publication Revision No. Control Table Rev. No. Date Contents Paper support Printer Manual Power cord Ink cartridges CD-ROM 2 Remove all the blue tape Vodafone Mobile Broadband Hotspot Vodafone MiFi 2352 OS: Android 4.0 For information Installation and Troubleshooting Guide. Model No. PAP2 Ver. 2. Voice Linksys is Designed for Vodafone Inland GPS Inc. Setting up the GPS Base Equipment Hardware First Find the best, most advantageous secure place to setup the GPS base equipment. Look for a high All rights reserved. Nokia, Nokia Connecting People, Nseries, N85, Navi, and Nokia Care are trademarks or registered trademarks of Nokia Corporation. Other product and company User Guide No User-serviceable parts inside. Refer servicing to qualified service Designed for Vodafone Except as expressly provided herein, no part of this manual may be reproduced, Usable microsd card. USB driver installation INSTRUCTIONS CLONING SOFTWARE CS-51 Designed by Vodafone This quick start guide will help you become familiar with our HDCVI DVR in a very short time. Before installation WMP54G Copyright and Trademarks Specifications are subject to change without notice. Linksys is a To use this website, you must agree to our Privacy Policy, including cookie policy. Manual, the. This manual applies to the Leica Viva Series. This manual contains. Built for the field Designed for extreme environments, you can alw. To get connected to SmartNet you will need the following: A valid SmartNet license A operational data connection (SIM, Mifi, etc).

Leica Viva TS11 is the most advanced manual total station with imaging and.Viva Series, Introduction. 2. Available documentation. The Leica GS14 is the most compact and powerful GNSS receiver. The Leica Geosystems Viva CS10 and CS15 controllers can be connected to an Echosounder by.Reload to refresh your session. Reload to refresh your session. This manual contains important safety directions as well as instructions for setting up the product and operating it. This manual contains important safety This manual contains important safety directions as well as instructions for setting up the product and operating it. This User ’ s Manual describes the hardware of SCS and how to connect the control bus inter- This manual contains important safety. You must have JavaScript enabled in your browser to utilize the functionality of this website. Figures quoted assume normal to favorable conditions. Times required are dependent upon various factors including number of satellites, geometry, ionospheric conditions, multipath etc. GPS and GLONASS can increase performance and accuracy by up to 30% relative to GPS only. A full Galileo and GPS L5 constellation will further increase measurement performance and accuracy.