godex 1200 manual

godex 1200 manual

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. Below is the general information: PRINTER PRODUCTS: Printers. All printers (excluding printheads) are warranted against defect in material or workmanship for twelve (12) months from the invoice date. Proof of shipment date (or Proforma Invoice date) is required to validate the warranty period. This warranty becomes void if the item is modified improperly installed, handled or used, or damaged by accident or neglect. SUPPLIES PRODUCTS: Supplies are warranted to be free from defect in material and workmanship for a period of six (6) months for media and twelve (12) months for ribbon from the date of shipment by Godex. No other warranties, expressed or implied, are given. Godex does not make any IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE in connection with its sale of products or services. With plastic outer casing, the EZ-1000 series is designed to be a lightweight and a low cost printer for large variety of printing requirement. Its features are as follows:. FUNCTION USBVCC 1-6. Printer Parts Please use the following diagrams to identify each printer part. Direct Thermal (DT): When printing, no ribbon is necessary; it only requires direct thermal media. Place the label roll onto the Label Roll Core, Loosen and lift the upper print mechanism by pressing the locking tensons. Feed the label through the two Label Guides to the Tear-off Bar. Align the label guides to the lablel edge. Connect the cable to the parallel port on the printer and on the PC. Power on the printer.Hold the stripper module and tighten the screws (28). Peel off the first label, and feed the liner through the roller and the peel off bracket. Flip close the stripper module. 10. Flip the cutter module (29) down to open the cutter. Notice: please refer to photo (A). Hold the cutter module and lock it with the two side screws (30).http://www.tcco.com.tw/upload/editor/161028289266.xml

• godex 1200 manual, godex ez 1200 manual, godex ez-1200 plus manual, godex ez-1200 printer manual, godex ezpi 1200 manual, godex 1200 manual, godex 1200 manual transmission, godex 1200 manual pdf, godex 1200 manual user, godex 1200 manual download.

Open and remove the plastic cover on the inner base. 3. Secure the PCB pillar onto the mainboard. 4. Check the pins where the memory is to be connected to, then plug the memory card onto the mainboard. When printing labels, pressing the Feed key, the printer will feed one label at a time; if the label is not sent out in a correct position, then please proceed with the Auto Sensing (see page 21). Direct Thermal (DT) When printing, no ribbon is necessary; it only requires direct therm al media. The setting value is from 0 to 19 and the default value is 15. Speed Set the speed of printing. Adjust Stop Position Default: 0 Set the stop position of printing. The setting value is from 0 to 10. The printer will go back to standby mode after prin ting a Self-Te st page. The printer will print out 3 labels that include user-defined variables a nd serial number. Follow the direction as shown in figure to feed the liner across the stripper. 11. Close the upper print mechanism and the stripper. 12. Press the FEED key to adjust the position of label and complete the installation. Note1 ? Please power off the printer before installing the cutter module. ? Note2 ? Do not cut self-adhesive labels. The traces of adhesive will pollute the rotary knife and impair safe operation. Align the WLAN module to the Ethernet port and plug into it. 14. Secure the module onto the back plate. 15. Thread the Module Connection Wire through the other con nection wires on the mainboard as the direction showed in figure. If the built-in memory is insufficient for storing label format s, graphics or fonts, users can us e CF Card as external memory to provide more memory space. Therefore when printing, it’s necessary to keep the top cover closed. Read more in our privacy policy. NiceLabel driver can obtain the feedback of the printer status. The status can be reported to and displayed in NiceLabel software. Corrected PnP ID for EZPi-1200 GZPL, EZPi-1300 GZPL and RT730x GEPL.http://xn--80aab8aioy.xn--p1ai/userfiles/acer-em61sm-em61pm-motherboard-manual.xml

Status Monitor application is also available in distribution.All new models, RT7 models and MX models are center positioned.RFID support removed on mobile QL (ZPL) models. RT860i, RT860i GEPL, RT860i GZPL, ZX1200i, ZX1200i GEPL, ZX1200i GZPL, ZX1300i, ZX1300i GEPL, ZX1300i GZPL, ZX1600i, ZX1600i GEPL, ZX1600i GZPL, MX30, MX30 GEPL, MX30 GZPL, MX30i, MX30i GEPL and MX30i GZPLPortuguese language is removed.Now they can change language settings if they have administrative rights. Now it works OK.This is corrected now.Thermal transfer mode disabled for EZ-DT2 GZPL and EZ-DT4 GZPL models.For this feature also NL must be updated (build after July 10th 2012).This is corrected now.Option enabled only on EZ-2xxx Plus and EZ-6xxx Plus series.New date formats were added.This is fixed now. This is corrected now.The status reporting issue was limited to NicePrintQueue, Enterprise Print Manager(EPM) and NiceLabel. UPC-E has been already work in this way. The reason is that old ZPL printers take the last 11 digits for data and not first 11 digit (of 12) for data.Everything that is send before the RFID command, prints fine. Now we have change the print stream, that RFID command is always the last of all elements. In this case there is no problems with the print getting cut off. GS1 Datamatrix barcode works from NiceLabel version greater than 5.2.2865. Please check also your printer's firmware version if support these barcodes.Only Flash RAM is available from now on.This is supported now. Also positioning of rotated 2D codes is corrected. (PDF417, Datamatrix)Following models added: EZ-DT2 GZPL, EZ-DT4 GZPL, EZ-1105 GZPL, EZ-1305 GZPL, EZPi-1200 GZPL, EZPi-1300 GZPL, EZ-2200 Plus GZPL, EZ-2300 Plus GZPL and EZ-1100 Plus GZPL.

Added missing USB PnP ID's for following models: Godex EZ-1100 Plus GEPL, Godex EZ-1105 GEPL, Godex EZ-1200 Plus GEPL, Godex EZ-1300 Plus GEPL, Godex EZ-1305 GEPL, Godex EZ-DT2 GEPL, Godex EZ-DT4 GEPL, Godex EZPi-1200 GEPL and Godex EZPi-1300 GEPLCommand cancels all format commands in the buffer. It also cancels any batches that are printing.A click on the shielded button and entering the credentials is all that is needed. Limitation is now set to 1200 dots.It will not jump back to its original position. User can print Registered Trade Mark, CopyRight, Trade Mark, Underwriters Laboratories approval and Canadian Standards Association approval symbols with typing A,B,C,D or E for internal text.This is corrected now.This is corrected now.Also when user will delete or install a new printer to the system, Status Monitor will detect the change by itself.This is fixed now.If set, then printer will not send some settings from Options and Advanced Setup tab. This feature is useful for printers with LCD display where user would like to set printer parameters (speed, darkness.) manually. This can be done with NL communication because this setting should driver get from NL. In this case leading zero's will not be printed, so if you want leading zero's you still have to imput 001 for example. WYSIWYG for non-leading zero's counters is not accurate because the printer gets the maximum counter length data and this can not be improved.User can open the Stock properties dialog and press OK to fix the problem (which is usually stock dimension). Stock size will be automatically adjusted.There is unknown command how to encode this characters into Code128.This only happens if barcode has variable contents.Accepted values can be in ASCII or HEX format.This is corrected now.This only happens when you are editing existing barcode font.Additional JJJ date mask was added for printers that support Julian Date.This is fixed now.Printer status was also not received immediately.

Status was changing between Not Accessible and ReadyNew version of driver will not lock the CHM any more and because of that reboot is not needed.Printer Error was displayed the whole timeMissing stocks have heights that are near the maximum printer's limit. The two illustrations as below show you how to install the ribbon depending on the ribbon type (ink side in or out). Note 2 Printer Setup Pass the ribbon under the print head and back up on the other side. You can only print when you see the “Ready“ status. M a k e sure th a t th e lab el senso r i s p os it io n ed co r r ectly. The start page will display the basic information of connected printer and your PC. Please contact your network administrator for related network setting information. Printer Configuration Set or change the configurations of connected printer. If no improvement is visible, turn the screws(A) clockwise or counterclockwise as far as possible and be sure to align with the indicator board and indicator line. Please check your inbox, and if you can’t find it, check your spam folder to make sure it didn't end up there. Please also check your spam folder. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at own expense. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. Replace only with the equivalent type recommended by the manufacturer. Direct thermal printing (DTP) Does not require a ribbon, only thermal paper. Attach it to the empty ribbon core.

The operator panel should now light up. On the Welcome screen, choose “Standard Installation”. Make sure that is done and then click “Next”. Just click “Other Choices” on Welcome Screen to access the files. Select the icon for the driver file and click it to start the installation. The Driver Wizard guides you through the installation procedure.Wait until copying is complete, then finish the installation. All manuals on ManualsCat.com can be viewed completely free of charge. By using the 'Select a language' button, you can choose the language of the manual you want to view. Perhaps the users of ManualsCat.com can help you answer your question. By filling in the form below, your question will appear below the manual of the Godex ZX1200i. Please make sure that you describe your difficulty with the Godex ZX1200i as precisely as you can. The more precies your question is, the higher the chances of quickly receiving an answer from another user. You will automatically be sent an e-mail to inform you when someone has reacted to your question. These limits are designed toThis equipment generates, uses, and canOperation ofIn a domestic environment this product may cause radioFederal Communication Commission Interference Statement. This equipment has been tested and found to comply with the limits for a Class BThese limits are designed toThis equipment generates, uses and can radiate radio frequency energy and, if notHowever, there is no guarantee thatIf this equipment does causeIncrease the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which theFCC Caution: Any changes or modifications not expressly approved by the partyThis device complies with Part 15 of the FCC Rules. Operation is subject to thePDF Version: 1.6. Linearized: No. Author: Sammy. Create Date: 2013:12:03 14:36:57Z. Has XFA: No. Creator: Sammy. Title: Microsoft Word - SMP-MANUAL.docx. Creator Tool: PScript5.dll Version 5.2.2.

Producer: GPL Ghostscript 8.15. Document ID: uuid:141155a1-b1f6-4670-951d-da4994e15fbb. Instance ID: uuid:5ae90cbe-2cb8-4723-a17a-9ed14cc00ddf. Page Count: 26. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. CD Including GoLabel software and user’s manual. Page 6 1 Barcode Printer 1. Page 7 1 Barcode Printer The Internal View of Printer RFID module RFID module Ribbon rewind hub Ribbon supply hub Print mechanism Platen roller Release lever for print head Paper guide Label tension guide Label supply hub Adjustable Sensor Paper guide 3 Label roll guide Page 8 2 Printer Setup 2.1 Loading the label roll This printer supports the following printing methods: Thermal transfer printing (TTP):Requires a ribbon for transferring a printed image to a medium. Direct thermal printing (DTP):Does not require a ribbon, only thermal paper. Page 10 2 Printer Setup Load the label roll into the printer as shown in the illustration. Pass it through the printer as indicated by the red arrows. Pass the label stock through the Adjustable Sensor and up to the tear-off plate. Page 11 2 Printer Setup 2. Return the print head release lever to its original position. 2 1 1 1. The labels pass between the wall of the printer housing and the adjustable paper guide. Then close the printer cover. Page 13 2 Printer Setup Pass the ribbon under the print head and back up on the other side. Attach it to the empty ribbon core. Page 14 2 Printer Setup 2.3 Connecting the Printer to the Host Computer 1. Please make sure that the printer is switched off. 2. Connect the power cord to the AC adapter and connect the adapter to the printer. 3. Connect the USB cable to the printer and host computer. 4. Switch on the printer. The operator panel should now light up. You will see the Welcome screen first. On the Welcome screen, choose “Standard Installation”. 2.

The wizard will then ask you to make sure your USB and power cables are connected and that the power is turned on. Make sure that is done and then click “Next”. 3. Page 16 2 Printer Setup 4. As the printer driver and GoLabel are installing, a screen will display a progress bar. 5. Once the installation is complete, you can start to make and print labels with GoLabel or through the printer driver. 6. As the optional steps, you can also print a test label or register your printer during the “Standard Installation” procedure. Select the icon for the driver file and click it to start the installation. 2. Follow the instructions on the screen. The Driver Wizard guides you through the installation procedure. Page 18 2 Printer Setup 4. Specify the port used to connect the printer to the host computer. 5. Enter a printer name and assign the appropriate rights. Godex ZX1200i Godex ZX1200i 6. Once the installation is complete, a summary of the printer settings is displayed. Wait until copying is complete, then finish the installation. Page 20 3 Printer Setting and Control 3.1 Operation Panel OPERATION TOUCH PANEL TOUCH PANEL FEED BUTTON POWER BUTTON POWER Button Press the POWER button to turn on the printer, and the START UP SCREEN appears. The printer is on “ready to print” status, the LCD screen should display the message “READY“ on the screen. When printer is turned on, hold and press down the POWER button for 3 second will turn the printer off. FEED Button Turn on the printer and press the FEED button. Page 21 3 Printer Setting and Control 3.2 LCD Interface Introduction Getting Started Press the POWER button to turn on the printer, and the START UP SCREEN appears. Power on If the printer is on “ready to print” status, the LCD screen should display the message “Ready“ on the screen. Use touch gestures to get around the Home screen and other screen for setting. Tap the screen with your finger or the stylus pen when you want to select on screen items such as settings icons.

ZX1200 V2. Page 22 3 Printer Setting and Control On the Ready Page, three function mode for setting. You can make various setting functions in FUNCTIONAL MODE. Page 23 3 Printer Setting and Control Main Printer Settings Darkness 10 Speed 6 Sensor Select Auto Select Media Type finish setting tap back to main page if Printer Setting LCD Language Codepage Label Setting Device Printer Control Recall Label Dump Mode do not save, tap system would not save any changes. Page 24 3 Printer Setting and Control Keyboard Mode When plug-in an USB keyboard to the printer, LCD touch panel will display “Enter Standalone”, press the “Y” key on keyboard to entering to the dialog for “Keyboard Mode” operation. LABEL-1 LABEL-2 FW:V2.000 15 Preview Label Preview Label Tap Preview Label can see printing label. Page 26 3 Printer Setting and Control 3.3 LCD Interface Function Main Page Main Printer Setting LCD Language Codepage Label Setting Device Printer Control Recall Label Dump Mode Setting items for printer, ex. Printing speed, darkness.Also includes a Printing Wizard for your ease of printing. More than 10 languages for printer setting It consists of a table of values that describes the character set for a particular language Setting items for printing label, ex. Rotation, Printing position offset. Page 27 3 Printer Setting and Control Device Page Device Buzzer Option Setting Smart Backfeed Serial Port Setting LAN Setting LCD Setting Clock Setting Setting off or on for buzzer Setting items for options, ex. Cutter, Label Dispenser, Applicator Choose ON. Printing labels would be back to start position. Setting items for Serial Port, ex. Baud Rate, Parity, Data Bits, Stop Bits. Setting items for LAN, ex. Port NO., DHCP, Dynamic IP, Default Gateway, Subnet Mask. Setting items for LCD, ex. You can only print when you see the “Ready“ status. ZX1200 V2.0000 Main Wizard Test If there is any printers error, the LCD screen will display the error screen to show the type of error.

You can fix the error according the notice. Page 31 3 Printer Setting and Control 3.4 Label Calibration and Self Test Label Calibration The printer can automatically detect and store label height. That means the host computer does not need to transmit the label height to the printer. Self Test Self-test function lets you check whether the printer is functioning normally. Press CALIBRATION BUTTON Press C-button for 2 seconds, it will make an auto-sensing to calibrate the label and ribbon’s parameters. Page 33 3 Printer Setting and Control 3.5 Error Alerts In the event of a problem that prevents normal functioning of the printer, you will see an error message on LCD screen and hear some beep signals. Please refer to below table for the error alerts. OPERATION TOUCH PANEL LCD TOUCH PANEL FEED BUTTON POWER BUTTON Operation Panel Status Type Print Head Error Beeps 2 x 4 beeps Description Solution The printing Open the print mechanism is not mechanism and correctly closed.Paper is finished. Media Error 2 x 2 beeps Replace the label roll. Possible reasons: the print medium has become trapped around the rubber roll; the Printer feed sensor cannot problem. Page 35 3 Printer Setting and Control 3.6 USB Host Definition: USB Host port supports either device:USB memory stick, keyboard or scanner. Purpose ? USB memory stick: It extends the user memory space up to 32GB for Graphic, Font, Label Format, DBF and Command files downloading. Page 36 3 Printer Setting and Control USB Keyboard. It is available on product CD or can be downloaded from official website. ZX1200 Click the magnifier icon to search the Godex printers which are connected via Ethernet port in you network environment. Once a connected Godex printer is detected, it will be listed on the start page. Page 39 4 NetSetting for Ethernet IP Setting The IP Setting tab can change the printer name, Port number, Gateway setting and the password for configuring the printer.

You can also set the printer’s IP address ether by DHCP or by Static IP. Page 40 4 NetSetting for Ethernet Alert Path Setting NetSetting will send the alert messages to designated mail account when the error happened on printer. The alert messages are sent by SMTP (Simple Mail Transfer Protocol) or SNMP (Simple Network Management Protocol). You can set or change the configurations of SMTP and SNMP on this “Alert Path Setting” tab. You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Page 41 4 NetSetting for Ethernet Alert Message Setting For the alert message notification function, you can decide which error cases need to be sent out to the operator. Moreover, the alert messages can be set to be sent by SMTP, SNMP or both. Page 42 4 NetSetting for Ethernet Printer Configuration Set or change the configurations of connected printer. Most of key settings for the printer operation can be done by this setting page. ZX1200i You can press “Set” button to apply the settings and “ReGet” button to refresh the setting values. Page 43 4 NetSetting for Ethernet User Command The “User Command” tab provides a communication interface for operator to control the printer. You can press “Send Command” button to send printer commands via Ethernet port and control the printer remotely. Page 44 4 NetSetting for Ethernet Firmware Download On “Firmware Download” tab, the current version of printer firmware will be showed on the screen. If you need to update the printer firmware, just specify the file location of firmware file and press “Start Download Firmware” button. Glue residue will be left on the cutter blade and impair its functioning. Page 46 5 Accessories 5.2 Installing the Cutter The Overview of the Cutter 1.Cutter module 2. Screw Unscrew the screw marked in the illustration on the front of the printer, which secures the lower cover plate. 1 2 Remove lower cover plate to the a little bit right then can get out.

Page 47 5 Accessories Connect the cutter cable connector to the cutter jack on the printer. Be sure the cutter module insert to printer properly. Page 48 5 Accessories Secure the cutter module on the printer housing using the screws. Finish the cutter module installed. Page 49 5 Accessories 5.2 Option Rewind Ribbon Hub Removing Ribbon Use tool to cut off the ribbon. Page 50 5 Accessories Pull open the knob, ribbon could be easy to remove. To install TPH module, follow the reverse order. Page 52 6 Maintenance and Adjustment 6.2 Adjusting the print line Open the printer cover. Repeat the adjustment process until printing quality has improved. Page 53 6 Maintenance and Adjustment 6.3 Adjusting ribbon tension You can adjust the ribbon tension by turning the ribbon shaft knob (see illustration) clockwise or counterclockwise. Page 54 6 Maintenance and Adjustment 6.4 Cleaning the thermal print head Dirt on the print head or ribbon may result in inadequate print quality (there are only partial images on the label). The printer cover should therefore be kept closed when possible. Keeping dirt and dust away from the paper or labels ensures a good print quality and a longer lifespan of the print head. Here is how you clean the print head: 1. Switch off the printer. 2. Open the printer cover. 3. Remove the ribbon. 4. Page 55 6 Maintenance and Adjustment 6.5 Adjusting the balance and print head tension Open the printer cover. If there is no printed image on one side of the paper, or the ribbon wrinkles, the print head pressure must be readjusted using the TPH spring boxes. Move the TPH spring boxes as shown in the illustration to change the print head pressure. Page 56 6 Maintenance and Adjustment 6.6 Ribbon shield settings The use of different ribbon materials may cause wrinkling of the ribbon, which in turn affects the print result as illustrated by the examples in (a) and (b). To change the print quality, you can adjust the ribbon shield screws.

If your print result looks like the example in (a), you need to turn ribbon shield screw clockwise. If your print result looks like the example in (b), you need to turn ribbon shield screw counterclockwise. Remove the cutter cover. Clean and remove jammed paper. Reinstall CUTTER back onto printer. Page 58 6 Maintenance and Adjustment 6.8 Troubleshooting Problem The printer is switched on but the LED does not light up. The LED lights up red and printing is interrupted. Godex is pleased to test non minimum print height and maximum print speed capability. Parallel port Handshaking Interface cable Pinout Pin No. USB Port Computer Connector:: Type A Pin NO. Function ? ? 1 VBUS 2 D- Ethernet (RJ-45) PIN NO. Printer Barcode Reader Label Maker Scanner. View and Download Godex EZPi-1200 user manual online. EZPi-1000 Series Barcode Printer. EZPi-1200 Printer pdf manual download. Also for: Ezpi-1300. We are now an approved UPS Broker for Canada (call 800-458-2390 for details). If you are using a foreign (outside of US) postal code, please call 1-800-458-2390 to place your order. Here's where you can downloads Free.Perfect for printing retail labels and tags, hospital and recreation wrist bands, plus other small, temporary labeling applications. For further. Godex EZ1100 Plus Barcode Printer. GODEX EZ120 Barcode Printer Multi-Purpose Thermal Transfer Desktop Barcode Printer.Barcode Printer. EZ-1100Plus Barcode Reader pdf manual download. Also for: Ez-1200plus, Ez-1300plus, Ez-1000plus. BARCODE PRINTER. RT200i Barcode Reader pdf manual download. Also for: Rt230i. View a manual of the Godex EZ-2300Plus below. Ribbons and labels sold separately. Please refer to our Return Policy before completing your purchase.Printer Barcode Reader Label Maker Scanner Print Server. View the Godex EZPi-1200 manual for free or ask your question to other Godex EZPi-1200 owners. Need a manual for your GoDEX EZ2350i Label Printer. Below you can view and download the PDF manual for free.

There are also frequently asked questions, a product rating and feedback from users to enable you to optimally use your product. Below are the 17 standard Godex printer forms. Line edits can be made by the end user. These form images are for reference purposes only, and are not actual size. Actual labels may vary slightly from form images. To see actual label dimensions, click here. High-performing and easy to use. BARCODE PRINTER. RT200i Barcode Reader pdf manual download. Please refer to our Return Policy before completing your purchase.