ge hybrid hot water heater manual

ge hybrid hot water heater manual

Volts Amps Watts for water heater GE Heat pump Product manual 10-2009 GE Heat pump Product manual 5-2011 GE Heat pump Product manual 2-2012 Geo-spring hybrid warranty Geo Spring controls Hand tools KleinHausfeld air powered Tekton. Page Count: 24 Manufactured under trademark license. OWNER’S MANUAL WATER HEATERS GeoSpring TM Hybrid Electric Residential 49-50300-2 10- 16 GEA GEH50DEEJS GEH50DFEJS GEH80DEEJS GEH80DFEJS SAFETY INFORMATION. 3 OPERATING INSTRUCTIONS Sizing information. 5 Controls. 6 Operational Modes. 7 ConnectPlus Module. 8 CARE AND CLEANING. 9 INSTALLATION INSTRUCTIONS. 1 3 TROUBLESHOOTING TIPS. 1 9 Fault Codes. 2 1 WARRANTY. 2 2 CONSUMER SUPPORT. 2 4 We take pride in the craftsmanship, innovation and design that goes into every GE Appliances product, and we think you will too. Among other things, registration of your appliance ensures that we can deliver important product information and warranty details when you need them. Register your GE appliance now online. Helpful websites and phone numbers are available in the Consumer Support section of this Owner ’ s Manual. Y ou may also mail in the pre-printed registration card included in the packing material. It may save you time and cost. Pay particular attention to the Safety Instructions. Failure to follow these warnings could result in serious bodily injury or death. Should you have problems understanding the instructions in this manual, or KDYH. DQ\? TXHVWLRQV?? 6723? DQG? JHW? KHOS? IURP? D? TXDOL?HG? VHUYLFH? WHFKQLFLDQ? RU? WKH? ORFDO? HOHFWULF? XWLOLW\? CAUTION Risk of Fire - Hydrogen gas can be produced in a hot water system served by this water heater that has not been used for a long period of time (generally two weeks or more). HYDROGEN GAS IS EXTREMELY FLAMMABLE!! To dissipate such gas and to reduce risk of injury, it is recommended that the hot water faucet be opened for several minutes at the kitchen sink before using any electrical appliance connected to the hot water system.http://medbioplast.com/klucharnet/images/yamaha-tech-manual.xml

• ge hybrid hot water heater manual, ge hybrid hot water heater manual system, ge hybrid hot water heater manual download, ge hybrid hot water heater manual pdf, ge hybrid hot water heater manual instructions.

If hydrogen is present, there will be an unusual sound such as air escaping through the pipe as the water begins to flow. Do not smoke or use an open flame near the faucet at the time it is open. W ARNING Risk of Fire - DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. Keep rags and other combustibles away. FOR INSTALLATIONS IN THE STATE OF CALIFORNIA California Law requires that residential water heaters must be braced, anchored or strapped to resist falling or horizontal displacement due to earthquake motions. For residential water heaters up to 52 gallon (236.4 L) capacity, a brochure with generic earthquake bracing instructions can be obtained from: Office of the State Architect, 400 P Street, Sacramento, CA 95814 or you may call 916.324.5315 or ask a water heater dealer. Applicable local codes shall always govern installation. For residential water heaters of a capacity greater than 52 gallons (236.4 L) consult the local building jurisdiction for acceptable bracing procedures. W ARNING If the water heater has been subjected to flood, fire, or physical damage, turn off power and water to the water heater. Do not operate the water heater again until it has been thoroughly checked by qualified service personnel. Safety Precautions A. Do turn off power to water heater if it has been subjected to overheating, fire, flood or physical damage. B. Do Not turn on water heater unless it is filled with water. C. Do Not turn on water heater if cold water supply shut-off valve is closed. NOTE: Flammable vapors may be drawn by air currents from surrounding areas to the water heater. D. If there is any difficulty in understanding or following the Operating Instructions or the Care and Cleaning section, it is recommended that a qualified person or serviceman perform the work.http://medica-brno.com/files/yamaha-tg33-manual.xml

State of California Proposition 65 Warnings: WARNING This product contains one or more chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. DANGER There is a Hot Water SCALD Potential if the control water temperature is set too high. To Adjust the Temperature Follow these steps: 1. Press the UP or DOWN arrow on the control panel key pad to desired temperature. 2. Press ENTER to accept the new setting. WATER TEMPERATURE ADJUSTMENT Safety, energy conservation, and hot water capacity are factors to be considered when selecting the water temperature setting of the water heater. Be sure to read and follow the warnings outlined on the label pictured below. This label is also located on the water heater near the top of the tank. The water heater is equipped with a temperature-limiting control (TCO) that is located above the heating element in contact with the tank surface. If for any reason the water temperature EHFRPHV. Once the control opens, it must be reset manually. Resetting of the temperature limiting controls should be done by a qualified service technician. CAUTION The cause of the high temperature condition must be investigated by a qualified service technician and corrective action must be taken before placing the water heater in service again. To reset the temperature-limiting control: 1. Turn off the power to the water heater. 2. Remove the jacket access panel(s) and insulation. The thermostat protective cover should not be removed. 3. Press the red RESET button. 4. Replace the insulation and jacket access panel(s) before turning on the power to the water heater. Safety Controls Always read and understand the safety instructions contained in the owner’s manual before adjusting the temperature setpoint. Contact a licensed plumber or the local plumbing authority for further information. OPERA TING INSTRUCTIONS: Sizing Information Filter is located on top of the water heater.

Press button and hold for 5 seconds to reset filter alarm. 8. Power Saver Override If operating with a demand response program through a local utility company, press and hold to bring unit out of Power Saver mode. 9. Appliance Communication Module Port For use with optional ConnectPlus communication module (see page 8 for details). 10. Anode Reset (on some models) When the red light is illuminated, the system has indicated that the anode rod is approaching end of life and it is recommended to replace it. Press button once to silence alarm. Press and hold for 10 seconds to reset the anode alarm after replacing. Call GE Appliances Service to replace the anode rod. After 30 seconds of inactivity, the display will go blank. However, the LED indicating the selected mode of operation will remain lit. To wake the control at any time to see the temperature setpoint, press any button on the control. Turning on the Water Heater There is no power button for this unit. Once the water heater is wired and power is supplied, it will be on. The display will show the current water temperature setting and an LED will illuminate indicating the current operating mode. Reported energy consumption is based on operating the unit in Hybrid mode at required Department of Energy (DOE) test conditions. Operating at lower temperature settings or in Heat Pump mode will provide even greater energy savings. To Adjust the Temperature Follow these steps: 1. Press the UP or DOWN arrow on the control panel key pad to desired temperature. 2. Press ENTER to accept the new setting.Check with your local utility for available rebates and requirements. IW??????? FX?P??? RU? ZLWKRXW? ORXYHUHG? GRRUV?? DV? VSHFL?HG? LQ? the installation instructions. The time it takes to heat the water is ORQJHU. LQ? WKLV? PRGH?? VR? LW? PD\? QRW? EH? VXI?FLHQW? LI? \RX? have a high-demand situation such as a large household or company.

Hybrid mode will allow the unit to perform like a standard electric water heater while providing significant energy savings. NOTE: Energy Guide unit performance, energy consumption and savings are based on non-ducted installations in Hybrid mode at required Department of Energy (DOE) test conditions. Operating in Heat Pump mode may provide a greater savings in energy and operating costs than the claimed savings. In this mode, the unit will use the electric heating elements only when the water demand rate is high. When using the heating elements, the water temperature will recover at a faster rate but it will use more energy to heat it. PRVW? HQHUJ\? HI?FLHQW? PRGH?? ? 7KH? XQLW? ZLOO? FRQWLQXH? WR? operate in this mode and does not indicate an operating issue. Vacation Mode This feature is recommended when you will be away IURP. HI?FLHQW? KHDWLQJ? PRGH? WR? FRQVHUYH? HQHUJ\? ZKLOH? WKH? heater is sitting idle. The unit will automatically resume heating one day before your return, so that hot water will be available. To set Vacation Mode: 1. Select Vacation by pressing the MODE button. 2. Input the total number of days you will be gone by pressing the UP arrow. The temperature setting will automatically reduce to 50 0 F (10 0 C) for 13 days. At the end of the 13th day, the previous operating mode and temperature setting will reset to ensure hot water is available upon your return. This unit has no power button, power can only be shut off at the circuit breaker or disconnect switch. If the water heater has an anode depletion sensing feature (some models) and the water heater cannot be drained, it is recommended to leave the power turned on with the water heater in vacation mode to ensure that the feature will continue to operate properly while still conserving energy. The water heater and piping should be drained if they might be subjected to freezing temperatures.

After a long shutdown period, the water heater’s operation and controls should be checked by qualified service personnel. Make certain the water heater is completely filled again before placing it in operation. NOTE: Refer to the Hydrogen Gas Caution in the Operating Instructions (see page 3). The ConnectPlus module will allow your water heater to communicate with your smart phone for remote monitoring, control of settings and vacation mode, and receiving alerts and notifications. Installation The ConnectPlus is equipped with magnets in the base of the module that enable it to attach to the painted PHWDO. WiFi Connectivity: For assistance with appliance or ConnectPlus network connectivity, please call 1-800- 220-6899. Notice: The Communication Port connection carries voltage not compatible to computers or accessories. Do NOT plug laptops, modems, routers, etc.Use only with designated GE Appliances Accessories. Connection to computers and accessories may result in product damage. Communication Port ConnectPlus module Routine Preventive Maintenance DANGER Risk of Scald - Before manually operating the relief valve, make certain no one will be exposed to the danger of coming in contact with the hot water released by the valve. The water may be hot enough to create a scald hazard. The water should be released into a s uitable drain to prevent injury or property damage. NOTE: If the temperature a nd pressure-relief valve on the hot water heater discharges periodically, t hi s m ay b e d u e t o th e rm a l expansion in a closed water system. Contact the water supplier or your plumbing contractor on how to correct this. Do not plug the relief valve outlet. Properly maintained, your water heater will provide years of dependable trouble-free service. Temperature and Pressure-Relief Valve: Once a year, it is recommended to lift and release the lever handle on the temperature and pressure-relief valve, located on the front-right side of the water heater, to make certain WKH.

Heating Elements and TCO: Once a year, it is recommended to inspect the heating elements, TCO, and wiring to each. Inspection should EH. FRPSOHWHG? E\? VHUYLFH? SHUVRQQHO? TXDOL?HG? LQ? HOHFWULFDO ? appliance repair. Most electrical appliances, even when new, make some sound when in operation. If the hissing or singing sound OHYHO. Draining and Flushing the Water Heater CAUTION Risk of Shock - Shut off power to the water heater before draining water. DANGER Risk of Scald - Before manually operating the relief valve, make certain no one will be exposed to the hot water released by the valve. The water drained from the tank may be hot enough to present a scald hazard and should be directed to a suitable drain to prevent injury or damage. A water heater’s tank can act as a settling basin for solids suspended in the water. It is therefore not uncommon for hard water deposits to accumulate in the bottom of the tank. To clean the tank of these deposits, it is recommended to GUDLQ. DQG? AXVK? WKH? ZDWHU? KHDWHU? WDQN? RQFH? D? \HDU?? ? 7R? GUDLQ ? the water heater, follow these steps: 1. Turn off power to the unit. Flushing should be done with an empty tank to promote additional removal of sediment. Note: See page 14 for product schematic. Use a flat slot screwdriver to turn valve. A clean air filter is important to get the highest efficiency. Occasionally this filter will need to be cleaned. When the filter requires cleaning, the Red light above the FILTER button will illuminate and an alarm will sound. Leave the power on. Remove the filter from the top of the unit. Squeeze two tabs and lift to remove the air filter. Once it has been removed, the filter can be vacuumed or wiped clean with a damp cloth or rinsed with warm water. Once the filter has been cleaned and dried, it can be replaced by aligning it into the slots in the top of the unit and pushing it down into place. After the clean filter has been reinstalled, press and hold the FILTER button to reset the alarm.

The unit will automatically revert to the previously selected operating mode. IMPORTANT: Filter must be cleaned when the alarm is displayed. A dirty filter will make the system work harder and result in a reduction of efficiency and possible damage to the system. In order to get the best energy efficiency available, make sure your filter is clean. NOTE: If the dirty filter alarm returns within a few days after cleaning and resetting, it may be an indication of a refrigerant leak. Further diagnosis by a service technician is necessary. The main drain is intended to carry all condensate away. If it is clogged, the heat pump will stop operating, the display will show F20, and an alarm will sound. Press any button to silence the alarm, then clear the condensate drain by removing any drain lines and connections, and clearing debris. Reattach drain lines and connections, then allow the water heater to run. The GeoSpring water heater will continue to produce hot water using the backup resistance heating elements until the condensate drain has been cleared, and is able to drain properly. Once the drain has been cleared, the unit will then be able to operate the heat pump again. Periodically inspect the drain lines and clear any debris that may have collected in the lines. See Installation Instructions for more information. Direct the main drain line into a drain Filter Slots Tabs Drain Line Connection 2YHUARZ Some areas have water conditions that may cause an odor to develop in the water heater. Warranty coverage for all other components remains intact, and is unaffected by this maintenance requirement. The replacement anode rod, and the inspection for consumption are not covered by warranty. Additional information for models with an anode depletion sensing feature (Anode button on the control): When the depletion-sensing anode rod nears end of life, the red light above the ANODE button will illuminate and the control will beep and display F16.

When this occurs, the anode rod must be inspected and replaced if the core wire DW. Call GE Appliances Service to order or to replace the anode rod. (See page 12 for instructions to change the anode rod.) GE Appliances Service: 888.4GE.HEWH (888.443.4394). Press the ANODE button once to silence the alarm. Once replaced, reset the alarm by pressing and holding the ANODE button for 10 seconds until the control beeps and the LED above the button turns off. If an Aluminum-Zinc anode rod is installed to address a water odor condition, the anode depletion sensing feature must be disabled. If disabled, annual inspections of the anode rod are required since the water heater will no longer be capable of alerting for a depleted anode rod. To disable the feature: 1. Upon power-up following an Aluminum-Zinc anode rod installation, the control will sound an alarm and F17 will display. To enable the feature if a new anode depletion sensing anode rod is installed, follow Step 2 above. Note: If the display is blank, press any button to wake the control before entering a button combination. NOTE: If the water heater has been installed with a device that periodically cuts power to the water heater, the accuracy of the anode rod depletion sensing feature may become compromised and anode rod inspection every 2-3 years is required. If the water heater will be inactive for a long period of time and the water heater cannot be drained, it is recommended to leave the power turned on with the water heater in vacation mode to ensure that the feature will continue to operate properly while still conserving energy. NOTE: Refer to the Hydrogen Gas Caution in the Operating Instructions (see page 3). Care and Cleaning Routine Preventative Maintenance If an Aluminum-Zinc or other non-sensing anode rod is installed, the anode depletion sensing feature must be disabled and the wire end taped (some models). 7.

Turn water supply on, open a tap to remove any air in plumbing system, inspect for leaks, then reassemble the unit in reverse order as shown in Illustration A, and turn the power on. Reset the ANODE button (some models) by pressing and holding for 10 seconds to indicate that a new anode depletion sensing anode rod is installed. CAUTIO N - IMPORT A N T SAFE T Y N OTICE This information is intended to use by individuals possessing adequate background of electrical, electronic DQG. The manufacturer or seller cannot be responsible for the interpretation of this information, nor can it assume any liability in connection with its use. T rim Ring T ape Process T ube Pinch Off T ape Corner and Edges Wires Wires Anode Rod Filter T rim Ring Front T op Cover Illustration A Illustration B Illustration C Anode Rod Illustration D POWER REQUIREMENTS Check the markings on the rating plate of the water heater to be certain the power supply corresponds to the water heater requirements. NOTE: 208V installations PD\. Do not install the water heater in outdoor, unprotected areas. Locate the water heater in a clean dry area as near as pra cti cal to t he a rea of g rea tes t heated water demand. Lon g uni nsula ted hot water lines can waste energy and water. Unit must be installed in a level location. Servicing the water heater requires proper installation such that the air filter, covers, trim ring, and front panels can be removed to permit inspection and servicing. Reference installation instructions found in this manual. Attic installations require access stairs and solid flooring with no exposed floor joists up to the installation location. Moving the water heater or other appliances to provide service to the water heater is not covered under warranty. If the ambient temperature is outside of this range, the heat pump will turn off and the electric elements will be used until the ambient temperature returns to within the operating range.

CAUTION Risk of Property Damage - The water heater should not be located in an area where leakage of the tank or connections will result in damage to the area adjacent to it or to lower floors of the structure. Where such areas cannot be avoided, it is recommended that a suitable catch pan, adequately drained, be installed under the water heater. LOCATION (CONT). Required clearances: 7KHUH. PXVW? EH? D? ??? ?????? FP?? FOHDUDQFH? EHWZHHQ? DQ\? object and the rear and sides of the water heater in the HYHQW. Installations that require ??? FOHDUDQFH? RQ? WKH? VLGHV? RU? UHDU? RI? WKH? ZDWHU? KHDWHU? IRU? earthquake straps are also acceptable. In these cases, additional clearance must be provided on the opposite side of the unit to allow for service access. The hot and cold water plumbing and electrical connections must not LQWHUIHUH. ZLWK? WKH? UHPRYDO? RI? WKH? ?OWHU? If a separate GE Appliances ducting kit is purchased, additional space is required above and to the rear of the water heater for installation. Consult the ducting kit manual IRU. GLVWULEXWRU?? 7KH? FDWFK? SDQ? VKRXOG? EH? ??? ????? FP?? minimum larger than the Water Heater base diameter. To prevent corrosion and improve Drain Valve access it is recommended that the water heater be placed on spacers inside the catch pan. Relief V alve Drain Condensate Drain Catch Pan Catch Pan Drain Model appearance may vary Drain must meet state and local codes. Contact your installing contractor, water supplier, or plumbing inspector for additional information. WATER SUPPLY CONNECTIONS Refer to the illustration below for suggested typical installation. The HOT and COLD water connections are FOHDUO\. PDUNHG? DQG? ? DUH? o?? 137? RQ? DOO? PRGHOV??:KHQ ? FRQQHFWLQJ? WR? WKH? LQOHW?RXWOHW? SRUWV?? WKH? XVH? RI? o?IHPDOH ? NPT tapered thread fittings with use of thread sealant is recommended.

The installation of unions is recommended on the hot and cold water connections so that the water heater may be easily disconnected for servicing if necessary. NOTE: Install a shut-off valve in the cold water line near the water heater. This will enable easier service or maintenance of the unit later. IMPORTANT: Do not apply heat to the HOT or COLD water connections. If sweat connections are used, sweat tubing to adapter before fitting the adapter to the cold water connections on heater. Any heat applied to the hot or cold water connection will permanently damage the internal plastic lining in these ports.The water heater warranty does not cover damage or failure resulting from operation with an empty or partially empty tank. Make certain the drain valve is completely close d. Open the shut-off valve in the cold water supply line. Open each hot water faucet slowly to allow the air to vent from the water heater and piping. A steady flow of water from the hot water fa u cet(s) indicates a full water heater. F11” fault code during installation: If the unit is SRZHUHG. If a 4-conductor wire is supplied to the water heater, cap the neutral, and connect the remaining wires as illustrated. NOTE REGARDIN G UTILITY POWER-MANAGEMENT DEVICES (Sometimes called Peak Load Reduction Switches): Some power-management switching devices or even VRPH. These devices must be removed from the circuit providing power to the water heater because of the potential unit damage noted above. To correct this fault, turn the power off to the unit, correct the wiring issue, then turn the power back on. RELIEF VALVE W ARNING Risk of Unit Damage - The pressure rating of the relief valve must not exceed 150 PSI (1.03 kPa), the maximum working pressure of the water heater as marked on the rating plate. A new combination temperature and pressure-relief valve, complying with the Standard for Relief Valves and Automatic Gas Shut-Off Devices for Hot Water Supply Systems, ANSI Z21.

22, is supplied and must remain installed in the opening provided and marked for the purpose on the water heater. No valve of any type should be installed between the relief valve and the tank. Local codes shall govern the installation of relief valves. Piping used should be of a type approved for hot water distribution. The discharge line must be no smaller than the outlet of the valve and must pitch downward from the valve to allow complete drainage (by gravity) of the relief valve and discharge line. The end of the discharge line should not be threaded or concealed and should be protected from freezing. No valve of any type, restriction or reducer coupling should be installed in the discharge line. Install the valve into an opening provided and marked for this purpose in the water heater, and orient it or provide tubing so that any GLVFKDUJH. The discharge opening must not be blocked or reduced in size under any circumstances. Installation Instructions INST ALLA TION INSTRUCTIONS The voltage requirements and wattage load for the water heater are specified on the rating label on the front of the water heater. The branch circuit wiring should include either: 1. Metallic conduit or metallic sheathed cable approved for use as a grounding conductor and installed with fittings approved for the purpose. 2. Nonmetallic sheathed cable, metallic conduit or metallic sheathed cable not approved for use as a ground conductor shall include a separate conductor for grounding. It should be attached to the ground terminals of the water heater and the HOHFWULFDO. W ARNING Proper ground connection is essential. The presence of water in the piping and water heater does not provide sufficient conduction for a ground. Nonmetallic piping, dielectric unions, flexible connectors, etc., can cause the water heater to be electrically isolated. The use of unauthorized energy-saving devices may shorten the life of the water heater and may endanger life and property.

Fan will turn on after 1 minute. This 2-minute off-time prevents compressor damage. A clicking noise may be heard during startup. 2 to 22 minutes Compressor turns on. Fan contin- ues to run. This 20-minute period is used to ensure the tank is full of water (Dry-fire prevention algo- rithm). 22 minutes and beyond Compressor turns off (Fan will run for 20 minutes after any compressor operation). Normal heating operation resumes. The water heater is operating in Hybrid mode. Quickly provides initial amount of hot water with heating elements, then switches to effi- cient heat pump for majority of heating. If the ambient temperature is outside of this range, the heat pump will turn off and the electric elements will be used until the ambient temperature returns to within the operating range. This provides great performance with less energy. WKDQ? QRUPDO?? 7KH? XQLW? ZLOO? EH? OHVV? HI?FLHQW? EXW? ZLOO? KHD W? water faster in response to long water draws. Unit will switch to the previous mode one day before you get back. This gives faster hot water recovery than Hybrid mode, but uses more energy. Q: The heat pump is not running its normal length of time. HQHUJ\? HI?FLHQW? PRGH?? 7KHVH? DUH? ERWK? QRUPDO? FRQGLWLRQV ? and do not indicate an operating issue. Q: Why isn’t the temperature setting always displayed on the control. A: The display screen will go blank after a period of inactivity in order to conserve energy. Pressing any button will wake the control and display the temperature setpoint. Anode Rod: Q: What does an anode rod do. A: The anode rod provides protection against corrosion of the water heater tank. The anode rod must be replaced before it is consumed and no longer offering protection against corrosion. Q: How to change the anode rod. A: Refer to page 12. Models equipped with an anode depletion sensing feature require a unique anode that can be ordered through GE Appliances Service. Q: What can I do about a sulphur smell coming only from my hot water.

A: Some areas have water conditions that may cause an odor to develop in the water heater. Aluminum-Zinc alloy replacement rods are available to address the condition. See page 11 for details. Save time and money. Review the chart below first and you may not need to call for service. Consider increasing the set temperature as described in the Wat e r T emperature Adjustment section.If the unit is full of water, turn the breaker off for about 10 minutes to allow the water temperature to stabilize, then turn the breaker back on. If the F1 1 code persists, schedule GE Appliances Service. Ensure that the anode depletion sensing anode rod or other GE Appliances approved anode rod is installed. Installation of an unapproved anode rod will VOID the warranty. Then read Electrical Connections section of the Installation Instructions, see page 16. Then contact the installer to verify electrical input to the water heater. See Thermal Expansion section on page 14. Contact a plumbing contractor to correct this.Probable refrigerant leak. Possible refrigerant leak. Probable refrigerant leak. If fault repeats after clearing, probable refriger- ant leak.Proof of the original purchase date is needed to obtain service under the warranty. W ARRANTY GE Appliances Hybrid Water Heater Warranty What Is Not Covered. Service trips to your home to teach you how to use the product. ? Improper installation, delivery or maintenance. ? Failure of the product if it is abused, misused, altered, used commercially or used for other than the intended purpose. ? Use of this product where water is microbiologically unsafe or of unknown quality, without adequate disinfection before or after the system. ? Replacement of house fuses or resetting of circuit breakers. ? Damage to the product caused by accident, lightning, fire, flood or acts of God. ? Incidental or consequential damage caused by possible defects with this appliance, its installation or repair. ?