galaxy 2000rs manual

galaxy 2000rs manual

The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid. In the event the alarm is triggered while the engine is remotely running, the remote start will immediately shutdown to prevent unauthorized users from attempting to drive the vehicle. Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transmitter buttons. If all four transmitters are to be used with both cars, program transmitters A and B into the first vehicle in the manner described above. Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature. Press button 3 to select it.Recall Alarm History Select Alarm History by pressing buttons 3 or 4 to highlight the clock. Press button 1 to select it.When programmed for full-time silent operation, the siren will sound only when the system is triggered. Once an Emergency Override Code is chosen and programmed during installation, the system can no longer be disarmed using the standard override procedure. WARNING: the Turbo Timer feature is not intended for use inside garages or other non-ventilated areas. Make sure to deactivate the Turbo Timer feature when parking in such areas.During proper operation, the shock sensor will detect impacts to the vehicle only and will not usually be triggered by slow rocking movements of the vehicle like those caused by wind.This type of door circuit is usually found on Ford vehicles.BLUE WIRE: (-)Trigger Input For Optional Sensor. Selects whether or not the system will automatically lock the doors 10 seconds after the ignition key is turned on. Override Code Set. Changes the Emergency Override Code for a higher level of security.http://www.empireevents.com/temp/vinney/HTML/userfiles/sony-dcr-dvd105-105e-605-605e-service-repair-manual.xml

• galaxy 2000rs installation manual.

When selected, the Auxiliary 2 output will activate when the system is armed.Select positive or negative wait to start input. 27. External Sensor Mode. Select sensor-2 input as an additional sensor input, or an external start trigger.Factory Defualt does not affect this setting.Negative Trigger Positive Trigger blue green Reverse Polarity Vacuum Adding Actuators Page 38 - Galaxy. When connected as shown below, disarming the system will unlock only the driver’s door. Pressing the disarm button again will unlock all doors. You must have JavaScript enabled in your browser to utilize the functionality of this website. Ignition Door Unlocking For added convenience, this feature automatically unlocks the doors after the ignition key is turned off. If the optional Passenger Unlock feature is installed, the Ignition Door Unlocking feature can be programmed to unlock only the driver door as a higher measure of safety, especially when children are present. The Ignition Door Unlocking feature may also be completely disabled if desired. Dome Light Activation If the optional Dome Light Activation feature is installed, the dome light will turn on when the system is disarmed using the Remote Transmitter, and remain on for 30 seconds or until the ignition is turned on. Auxiliary Function Outputs The Galaxy Starter system is equipped with 3 Auxiliary Channel Outputs allowing the convenience features of the system to be further expanded. Turbo Timer Feature The optional Turbo Timer feature allows vehicles with turbocharged engines to remain running after the ignition key is removed, for proper cool-down of the turbocharger. The Turbo Timer feature requires connection to the vehicle?s parking brake wire and is compatible with most gasoline powered engines, and diesel engines where a glow plug connection is not required. The Pulsed operation setting allows an output to activate as long as the button is held.http://mantyobras.com/userfiles/sony-digital-handycam-8-manual-dcr-trv350.xml

The Timed operation setting allows an output to activate when the transmitter button is pressed, and remain activated for 10 seconds or until the transmitter button is pressed again. Note: With the optional ScyNet network interface and Wizard software, the timed output can be programmed for any time between 1 second and 255 seconds. The Latched operation setting allows an output to activate when the transmitter button is pressed, and remain activated until the transmitter button is pressed again. You can simply remove the item from your cart. You have no obligation to purchase the product once you know the price. You can simply remove the item from your cart. Use Peatix for any event and ticketing needs! Co-organizers can edit group and event pages, access sales and attendee information, manage ticket sales and more. An LCD remote can display warning icons when the doors, trunk or hood are open. If your vehicle is tampered with, some remotes display what part of the vehicle was affected. Lock and Unlock Outputs, and Compatible with All Vehicles. Available for the Blackberry, Android, and iPhone, works with most vehicle. Click here to register and keep the warranty active. Pre-wired Super Bright Blue LED, Valet Switch Connectors. Plug-in user programmable Coded Override Switch. Horn Or Ignition 3 (Programmable) (-) Output. Passenger Unlock (-) Output. Two Auxiliary Channels with Selectable Output Types, (Pulsed, Timed or Latched). User-Selectable Passive Locking. User-Selectable Auto-Relocking. User-Selectable AutoLock -With Ignition or RPM dependant. Remote Keyless Entry and Accessory Activation Even in Valet Mode. Remote-Controlled Courtesy Lighting. AutoActivation Upon Locking And Unlocking of Auxiliary 2 Auto Unlock with Auxiliary 1 Activation (Trunk Release Output). Smart Remote Trunk Release. Additional Information. Two Sleek 5 Button Code hopping remote controlsUse Our Vehicle Application Guide to Build a System.

Description: Galaxy Mobile 500 uses your Smart Phone As a two way fob. Related Manuals for Scytek electronic Galaxy 5000RS. The Galaxy is a key fob automobile remote. Program the Galaxy to lock and unlock doors, start and cut off the manual gps topcon, droid eric cell phone manual Government library vision statement, Sony music entertainment mission statement, Nba fantasy draft guide, A cover letter example, Writing a church report. By clicking ACCEPT or continuing to browse the site you are agreeing to our use of cookies. Find out more here. Are you sure to remove this product? Galaxy Buds work rightout of the box, connecting with your Galaxy devices in an instant via Bluetooth to get you up to the beatand well on your way. Galaxy Buds feature a newly refined design that makes themso compact they fit in comfortably with the rest of your belongings. They also come in standard colour options that blend right in to your daily routine. Galaxy Buds recognize your surroundings, switching between inner and outermics to keep unnecessary noise out of your conversation. Galaxy Buds let you quickly shift yourfocus to your surroundings without taking them off, so you’ll never miss what’s coming and going. Galaxy Buds let you pair and switch seamlessly between your Galaxy devices so you don’t miss out on any of the action. And when you’re done, Galaxy Buds connect to device-to-device wireless power-sharecompatible Galaxy devices. So, your Buds are always ready to go. All functionality, features, specifications, GUI and other product information provided in this web page including, but not limited to, the benefits, design, pricing, components, performance, availability, and capabilities of the product are subject to change without notice or obligation. The contents within the screen are simulated images and are for demonstration purposes only. All features, specifications and prices are subject to change without prior notice.

Model availability may vary from location to location. And click on 'Buy Online' or copy the Quote id. Click here for privacy policy for Samsung. Click here for privacy policy for Servify Are you sure to proceed? Are you sure to proceed? Are you sure to proceed? You can redeem Galaxy Assured Values at any time within the program period. The Galaxy Assured values for different time periods are given below in the table The device can be redeemed at www.cashify.in any time within 12 months. The exchange value would be applicable as per tenure of purchase (table below). If eligible, you will see an estimated trade-in value. The manufacturer will repair or replace at its option, and free of charge for the first twelve (12) months, any part that proves defective in material or workmanship under normal installation, use, and service, provided the product is returned to the manufacturer freight prepaid. With proper installation this system will provide superior protection and performance for many years to come. Page 6 Remote Transmitters Standard Remote Transmitter Description LED LED Button 2 Button 1 Button 1 Button 2 Button 3 Button 4 Button 5 Button 3 Button 4 Button 5 T5-SP T5 Depending on the model chosen, the Galaxy 5000RS-DBP Series will be supplied with one or two T5 or T5-SP 5-button Remote Transmitters that are used to control the system’s operations. Note: Up to 4 one-way transmitters can be programmed to operate the system. Any previously stored transmitter will be erased if it is not programed within the following sequence To program the transmitter(s): 1. Turn the ignition key On, Off, On, Off, and back On. Page 8 2-way LCD Remote Transmitter Description Button 1 Button 2 Button 3 Button 4 Button 5 Depending on the model chosen, the Galaxy 5000RS-DBP-2W Series will be supplied with one or two 2-way LCD Remote Transmitters, offering increased range and confirmation of any activated features.

Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system’s Panic feature. Button 1 also locks the doors when the system is in Valet Mode. LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. SND sound function selects the transmitter's confirmation mode - Tone or Vibration mode. Page 14 PAGER PARAMETERS SETTING Press and hold Buttons 2 and 3 until pager program features are displayed. Select pager setting by pressing buttons 1 or 2 to highlight the pager. Press button 3 to select the pager. Press button 3 to select it. Save the changes by pressing button 5. START SET AUTO ST ON TIME: 08:00A Setting Alarm Clock Select Alarm setting by pressing buttons 1 or 2 to highlight the feature. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Press and hold Buttons 2 and 3 until pager program features are displayed. Select system setting by pressing buttons 1 or 2 to highlight the pager. Press button 3 to select the system features. Page 17 Setting AutoStart Cold Temperature Threshold Select Cold Temp start setting by pressing buttons 1 or 2 to highlight the feature. Save the changes by pressing button 5. AUTOSTART SET COLD TEMP TEMP: - 11oF Security system responce Setting AutoStart Hot Temperature Threshold Select Cold Temp Time setting by pressing buttons 1 or 2 to highlight the feature. Page 18 Synchronize System and Pager Clocks Select Clock Sync setting by pressing buttons 1 or 2 to highlight the pager. Pager Clock Sync This feature synchronizes the pager clock to the security system time of a day clock. Select Pager Clock Sync by pressing buttons 1 or 2 to highlight the feature. Start Time 2 This feature sets the system Autostart 2 time. Select Sytem Clock Sync by pressing buttons 1 or 2 to highlight the feature. Out of Range Report pager report if no responce from the unit. Battery Status: displays remaining battery life.

The LED indication will repeat 8 times. Note: If the code set procedure is not properly performed, turn off the ignition and begin again. Page 28 Automatic Start Mode Automatic Start feature has three modes that will start the vehicle every one or two hours within a 24 hour period. 1. Timer Only Mode (factory default) The Automatic Start feature starts the vehicle automatically every one or two hours and runs for the preset Run Time. (15 or 25 min) Auto Start on Timer Mode: 1. Turn Ignition switch Off and wait for 3 seconds. 2. Turn Ignition switch On and Off three times ending with Ignition in Off position 3. Press the Valet switch immediatly after. Page 29 Manual Transmission Remote Start Features Model: Galaxy 5000RS-DBP-M 1- Tach wire must be connected, The system must learn RPM. 2- Hand brake must be connected. 3- Door trigger must be connected 4- Clutch override installed NOTE: MUST USE RELAY, SEE PAGE 26. Page 30 Extended Features Ignition Door Locking For added safety, the Ignition Door Locking feature allows vehicles equipped with power door lock systems to automatically lock the doors when the ignition is turned on. If a door is open when the ignition is turned on, the Ignition Door Locking feature is disabled to protect against locking the keys inside the vehicle. If RPM is selected Doors will lock when engine RPM exceed 2.5 times the idle. Page 31 System Installation 1. 2. Thoroughly read and become familiar with the installation instructions before beginning the installation. Do not mount the main unit in the engine compartment. Choose a mounting location that will not be easily accessible to a thief, and will not interfere with the operation of any vehicle components such as foot pedals, steering column, air vents, seat rails, etc. Do not mount the control unit until after setting the internal jumpers and performing a complete operation check of the system.

Connect to the battery or constant power wire at the ignition switch with a minimum 25 Amp supply. Remove the fuse until the installation is complete and all wiring is checked. Connect to the battery or constant power wire at the ignition switch with a minimum 25A supply. This type of door circuit is usually found on Ford vehicles. Pin 12 GREEN WIRE: Negative Door Input (-). Connect to the door switch circuit wire that shows ground when the door is open. The switch must provide a ground output when switch is opened. Pin 14 ORANGE WIRE: Armed Output (-) 500 mA. Page 36 System Programming Entering System Programming This system is compatible with both the LCD two way transmitter or the standard transmitter, all system programming can be performed using either one. Door Lock Pulse Length. Selects between a 1, 3 or 0.1 seconds output for door locking and unlocking. Program to 3 seconds for vehicles equipped with vacuum door locking systems. 8. Passive Door Locking. Selects whether or not the system will automatically lock the doors during Passive Arming and Auto Rearming mode. 9. Remote Start Confirmation Chirps. When enabled, system chirps before starter activated. When disabled, no chirps will sound upon start. 7. Page 39 16. Auxiliary 3 Output Mode. Selects between Channel 3, Factory Rearm output, or third Ignition ouput. 17. Lock After Start. When selected, the doors will automatically lock after remote starting. Using button 3 disabled Mp Siren Mode. 18. Lock After Shutdown. When selected, the doors will automatically lock after remote shutdown. 19. Engine Run Time. Selects between 15 or 25 minutes for the remote start run cycle. 20. Automatic Start Mode. Page 40 28. Siren Mode. Selects standard siren (defualt) or MP Player Siren. 29. Turbo Timer. When enabled, if the emergency brake has been applied Ignition power will be kept On for a predetermined time (2 minutes Factory Default) from the application of the emergency brake. 30. Extended Parking Lights.

When Enabled, upon Disarming Parking lights will turn On for 30 seconds 31. Warn-Away Pager Report. When Enabled, Warn-Away report will be sent to the pager. Page 43 Two Stage Door Lock Diagrams The Galaxy 5000RS-DBP Series is equipped with a dedicated Passenger Unlock output allowing Two Stage Door Lock operation. When connected as shown below, disarming the system will unlock only the driver’s door. Page 44 Two Stage Door Lock Diagrams cont’d Two Stage Reverse Polarity Two Stage Adding Actuators Page 40 - Galaxy 5000RS-DBP Page 45 Technical Information FCC ID: OARRXAM2000 This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. A copy of the original purchase and installation receipt must accompany any products returned for warranty service. The manufacturer of this theft deterrent system makes no warranty against the theft of the vehicle or its contents. This warranty is not to be construed as an insurance policy against loss.With proper installation this system will provide superior protection and performance for many years to come. To ensure the safety and security of the system while it is remote started, the Galaxy 5000RS-DBP Series employs several safeguards. In the event the alarm is triggered while the engine is remotely running, the remote start will immediately shutdown to prevent unauthorized users from attempting to drive the vehicle. The system is equipped with a hood pin input to prevent access to the engine compartment while the vehicle is remotely running. The Valet Mode prevents the remote start feature from operating in the event the vehicle is to be serviced. Finally, the brake pedal also acts as a safety by shutting down the remote start when pressed. Additionally, many features of these systems have selectable options that must be activated or programmed during the system s installation. These items will be identified in the following sections.

Please discuss these features and any questions you may have regarding the installation of this product with Your Authorized Dealer. Galaxy 5000RS-DBP - Page 1 Note: Using the optional PC or Pocket PC interface with the network software, it is possible to reconfigure the functionality of the transmitter buttons. The standard (default) setting for operation of the transmitters is described below. Button 1 Arms and Locks the system and when held for 5 seconds, activates the system s Panic feature. Button 2 Disarms and Unlocks the system. Pressing Button 2 again operates the Passenger Unlock feature (if installed). Button 2 also unlocks the doors when the system is in Valet Mode. Button 3 Activates the Auxiliary 1 output. This output will remain on for as long as the button is pressed. Button 4 Activates the Remote Start feature. Button 5 is the Page Shift button. Each time the Shift Button is pressed, the LED on the transmitter will illuminate and the transmitter functions will shift to the next page, allowing access to another set of features. Once shifted to another page (there are 4 pages total), the transmitter will remain on that page for 10 seconds or until a button is pressed, then it will return to page 1. Under normal operation, only pages 1 and 2 are used. Pages 3 and 4 are usually used for Two Car Operation (see page 3) or optional expansion modules. Shift then Button 3 Activates the Auxiliary 2 output. Page 2 - Galaxy 5000RS-DBP. The LED will illuminate. 3. Press Button 1 on the first transmitter. Two Car Operation If two vehicles are equipped with the Galaxy 5000RS-DBP Series systems, for convenience both can be operated using the same remote transmitter. If all four transmitters are to be used with both cars, program transmitters A and B into the first vehicle in the manner described above. Program transmitters C and D by pressing the Shift button twice before performing steps 3 and 4 above.

When finished programming the first vehicle, program transmitters C and D into the second vehicle as normal, then program transmitters A and B by pressing the Shift button twice before performing steps 3 and 4 above. When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing the Shift button twice and the desired function button. Battery Replacement The T5-SP Remote Transmitter uses two 3 volt lithium batteries (type CR2016) The T5 Remote Transmitter uses a 12 Volt lithium battery (type GP23A) which will require replacement in time. Depending on the amount of use, the batteries may last up to six months or more before they need replacement. In order to change the battery, first remove the screw from the back of the transmitter and separate the top and bottom halves of the case. While replacing the battery make sure that the positive and negative terminals are positioned correctly, then carefully reassemble the transmitter case. Galaxy 5000RS-DBP - Page 3 Page 1 Button 1 Arms and Locks the system and when held for 5 seconds, activates the system s Panic feature. Button 3 Activates the Auxiliary 1 output normally used for trunk release (note trunk icon on button). Button 5 is the Confirmation, Programming and the Page Shift button. Quickly pressing button 5 will activate the Page 2 function. Button 3 Activates the Auxiliary 2 output. Button 4 Aux 3 or Factory Rearm output. Button 5 Not Implemented. The LED will illuminate. Page 4 - Galaxy 5000RS-DBP LCD Transmitter Battery Replacement Your Galaxy Remote Transmitter uses a 1.5 volt AAA alkaline battery, which will require replacement in time. Depending on the amount of use, the battery may last up to 3 months before it needs replacement.

When the battery needs replacing, the system s operating range will decrease, the LCD display will show only one of three bars in the battery icon, or the display and sounds may suddenly stop and start as the battery voltage drops below minimum. In order to change the battery, first slide the battery door locking pin to the side. Carefully slide the battery cover downward until it is free. Setting The Time The LCD display is equipped with a 12-hour clock that in addition to displaying the time, offers an alarm clock function as well as a remote activation timer. To set the time: 1. Press and hold Buttons 2 and 3 for three seconds. The remote will beep two times and three bars will be shown indicating time set mode is entered. 2. Press and release Button 2 until the correct hour is displayed. (hold button to scroll). 3. Press and release Button 3 until the desired minute is displayed. (hold button to scroll). 4. When the desired time is displayed, press Button 5 to store. The remote will beep 3 times to indicate the time has been set. Setting The Alarm Clock The alarm clock function can be set to play an alert melody at a specific time of day. To set the alarm clock function: 1. Press and hold Buttons 2 and 3 until the remote beeps three times. The alarm clock bell and three bars will be shown indicating alarm clock set mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. Press Button 3 until the desired minute is displayed. The button may be held down to scroll faster. 4. When the desired time is displayed, press Button 5 to store. The remote will beep 3 times to indicate the alarm clock has been set. To disable the alarm clock function: 1. Press and hold Buttons 2 and 3 until the remote beeps three times. The alarm clock bell and three bars will be shown indicating alarm clock set mode is entered. 2. Press Button 1 to disable the alarm clock. The remote will beep 3 times and show OFF to indicate the alarm clock has been disabled.

Setting The Daily Start Function ( transmitter must be within 1500ft to reliably start) The Daily Start Function provides a timer that allows the vehicle to automatically remote start at a preset time of day, everyday until the feature is turned off. Galaxy 5000RS-DBP - Page 5 The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 2 until the desired hour is displayed. 3. Press Button 3 until the desired minute is displayed. The remote will beep 3 times to indicate the daily start function has been set. To disable the daily start feature: 1. Press and hold Buttons 2 and 3 until the remote beeps four times. The fan and clock will be shown indicating daily start mode is entered. 2. Press Button 1 to disable the daily start function. The remote will beep 3 times to indicate the daily start function has been disabled. Setting The Automatic Cold Start Temperature (2 step procedure, for second step see page 7 under c o ) The Automatic Cold Start setting sets the temperature threshold. If automatic start is set to cold temperature setting,the starter will activate every 2 or 4 hours if the temperature drops bellow the set value. 1. Press and hold Buttons 2 and 3 until the remote beeps five times.The remote will display the temperature and beep 3 times then 4 times to indicate the set temperature. Setting The Automatic Hot Start Temperature (2 step procedure, for second step see page 7 under h o ) The Automatic Hot Start setting sets the temperature threshold. If automatic start is set to hot temperature setting, the starter will activate every 2 or 4 hours if the temperature rises above the set value. 1. Press and hold Buttons 2 and 3 until the remote beeps six times.The remote will display the set temperature and beep 3 times then 4 times to indicate the set temperature. LCD Backlight Transmitter Button 5 is used for confirmation, transmitter programming, as well as activation of the LCD backlighting for use in the dark.

Press and release button 5 momentarily to activate the LCD backlight. System Confirmation The 2-way transmitter's confirmation feature allows the current vehicle status to be displayed at any time. To display system status: 1. Press and hold Button 5 until the display shows CON. The transmitter will beep once. 2. Release Button 5. The transmitter will beep once. The LCD panel will display the current system status. Programmable Functions using the LCD Transmitter Pressing and holding transmitter button 5 will scroll through several transmitter programmable options - DEG, CHP, SND, PSV, VAL, O C and O h. DEG Check the temperature inside the vehicle 1. Press and hold Button 5 until the display shows DEG The transmitter will beep twice. 2. Release Button 5. The transmitter will beep four times. The LCD panel will display the temperature inside the vehicle Page 6 - Galaxy 5000RS-DBP. The transmitter will beep three times. 2. Release Button 5. The transmitter will beep once. Set the transmitter confirmation tones ON or OFF: 1. Press and hold Button 5 until the display shows SND. The transmitter will beep four times. 2. Release Button 5. The transmitter will beep once. Enable or disable the passive arming mode: 1. Press and hold Button 5 until the display shows PSV. The transmitter will beep five times. 2. Release Button 5. The transmitter will beep once. Set or reset the Valet mode: 1. Press and hold Button 5 until the display shows VLT. The transmitter will beep twice and the siren will chirp twice if the Valet mode was reset. C O Auto Start Cold Temperature Activation Mode. 1. Press and hold Button 5 until the display shows C O. The transmitter will beep 7 times. 2. Release Button 5. The transmitter will beep once. The LCD panel will show Auto Start Cold Temperature setting. 3. Press and hold Button 5 until the display shows CON. 4. Release Button 5. The transmitter will beep once.

Galaxy 5000RS-DBP - Page 7 Button 1 also locks the doors when the system is in Valet Mode. To display system status: 1. Press and hold Button 5 until the display shows CONFIRM. The panel will display the current system status. Galaxy 5000RS-DBP - Page 9 Select pager setting by pressing buttons 1 or 2 to highlight the pager. START SET AUTO ST ON TIME: 08:00A Page 10 - Galaxy 5000RS-DBP. Save the changes by pressing button 5. CLOCK ALARM ALARM ON TIME: 08:00A Symbol is displayed when Alarm Clock is enabled. TIME DATE START TIME ALARM CLOCK SOUND ON BACK Galaxy 5000RS-DBP - Page 11 Press button 3 to select it. SIREN CHIRP PASSIVE ARM COLD TEMP HOT TEMP BACK Sytem Responce FEATURE ON Page 12 - Galaxy 5000RS-DBP Press button 3 to select it. Save the changes by pressing button 5. AUTOSTART SET COLD TEMP TEMP: - 11 o F Security system responce Setting AutoStart Hot Temperature Threshold Select Cold Temp Time setting by pressing buttons 1 or 2 to highlight the feature. Save the changes by pressing button 5. AUTOSTART SET HOT TEMP TEMP: 110 o F Security system responce Galaxy 5000RS-DBP - Page 13 Press button 3 to select the pager. PGR CLK SYNC SYS CLK SYNC START 1 TIME START 2 TIME EXIT AUTO CLOCK SET Security system responce System Clock Sync This feature synchronizes the system clock to the pager time of a day clock. PGR CLK SYNC SYS CLK SYNC START 1 TIME START 2 TIME EXIT SYSTEM CLOCK SET Security system responce Start Time 1 This feature sets the system Autostart 1 time. Page 14 - Galaxy 5000RS-DBP. Recall Alarm History Select Alarm History by pressing buttons 3 or 4 to highlight the feature. Press button 1 to select it. Galaxy 5000RS-DBP - Page 15 ENABLE COLD START Auto Start Cold Temperature Activation Mode. 1. Press and hold Button 5 until the display shows ENABLE COLD START. 2. Release Button 5. The transmitter will beep. The display will show Auto Start Cold Temperature setting. 3. Press and hold Button 5 until the display shows CONFIRM. 4. Release Button 5.