Demco Tow Dolly Manual

Demco Tow Dolly Manual

We feel you have made a wise choice and hope you are completely satisfied with your new piece of equipment.Be certain that your towing vehicle has the capacity to tow a tow dolly and towed vehicle combination.If your answer is YES, we thank you for your attitude and believe your towing experience will be a safe and pleasant one. Be sure your cooling system is in top shape, and adequate for towing anticipated load. In addition to being illegal in most states, carrying passengers in a towed vehicle exposes those passengers to risk of exhaust gas asphyxiation. Lighting Requirements Even though tow dollies have operating lights, law requires that a vehicle-in-tow be equipped with functioning stop, turn and running lights. ACCIDENTS Move all vehicles completely off the road. Get everyone out of the vehicle and off the road. Call police. Demco wants you to have a safe towing experience. Read these instructions carefully, read fender decals on tow dolly,. Use care when servicing or injury may occur.Check tightness of bolts periodically, using bolt chart as guide. Replace hardware with same grade bolt. NOTE: Unless otherwise specified, high-strength Grade 5 hex bolts are used throughout as- sembly of equipment. Install rear hole in the fender trough.Do not attempt while tow dolly is loaded or hooked up. Pull retainer clip from bottom of tongue locking pin. Lift locking pin out of tongue pivot.Do not attempt while tow dolly is loaded or hooked up. Locate ramp locks at inside center of ramps. Pull ramp lock straight out as far as it will go. Lift ramp lock up as far as it will go and allow lock to slide in until it stops. Make sure that the hitch and the hitch ball are in good condition and not rusted, loose or stripped. Recommended ball height is 18” to the top of the ball. Make sure hitch is locked down. Make sure the car is centered on the platform. Towed vehicle tires must fit in wheel troughs without overhanging sides. Never unhook tow Step 10.http://angkorphotographyguide.com/userfiles/coleman-powermate-air-compressor-27-gallon-manual.xml

• demco tow dolly manual, demco tow dolly manual, demco tow dolly manual, demco tow dolly manual pdf, demco tow dolly manuals, demco tow dolly manual free, demco tow dolly manual instructions, demco tow dolly manual parts, demco tow dolly manual for sale, demco tow dolly manual online, demco tow dolly manual 2017, demco tow dolly manual.

Thread tie-down strap through the slotted tube on dolly coupler from towing vehicle, before unloading tow the tie-down winch. Pull approx. 6” of strap through this slot. dolly. Make sure that platform and vehicle are straight. Re- Begin tightening strap making sure the tail becomes enclosed install driveshaft. Uncross wires, then while e Rue Ring to remove from pin. Model DA91 Brake Actuator SURGE BRAKES PARTS LIST REF. Table of Contents General information. Good safety requires that you familiarize yourself with various safety signs, type of warning, and particular function related to that area, that requires your SAFETY AWARENESS.Check tightness of bolts periodically, using bolt chart as guide. NOTE: Unless otherwise specified, high-strength Grade 5 hex bolts are used throughout assembly of equipment. The short side of the hook must face the rear of the TOW-IT. Step 5. With someone safely guiding you, slowly drive ve- hicle onto platform FRONT FORWARD. To pull the TOW-IT empty, make sure tie-down the auto tire. The picture above shows a correct fitting strap.Tires and lights are not included in this warranty. 5) Any Demco Tow-It that has been loaded in excess of the load capacity stated on the tow dolly identification label. Tires are warranted by the manufacturer against defects in materials and workmanship, but not against road hazards. Then slide the Actuator, brake line, and lift handle onto tongue and attach with supplied fasteners. Make sure the tie-down str Page 19 and 20: Page 193866141516171819262721303132 Page 21 and 22: LICENSE PLATE BRACKET ASSEMBLY31244 Page 23 and 24: DISC BRAKE PARTS BREAKDOWN AND PART Page 25: Wiring DiagramFender WiringOn the l Page 28 and 29: OPTIONAL WINCH517643PARTS LISTREF.N Page 30 and 31: Page 30 Page 32: P.O. BOX 1894010 320th St., BOYDEN, Thank you, for helping us keep this platform clean. The editors will have a look at it as soon as possible.http://esperanzadeavila.com/fotos/coleman-powermate-black-max-air-compressor-manual.xml

If you are looking for a car tow dolly, the Demco tow dolly, more specifically the Kar Kaddy SS 460, is a great RV tow dolly.Accessories for your Demco tow dolly. Amazon.com: tow dolly parts. Easy online ordering or call 800-298-892 The KarKaddy SS, KarKaddy 3, and the new KarKaddy X are all high-quality tow dollies that provide durable, safe, and effective means of transporting your vehicle behind a motor home. FREE Shipping. Get it as soon as Tue, May 5. Any part of the Demco Kar Kaddy, except tires and lights, found, in the judgement of the manufacturer to be defective in materials Warrantor has a policy of continuous product improvement. Skip to main content. Croft Trailer Supply is your One-Stop Trailer Shop.Tow Dolly Replacement Parts. 03772X --- CROFT Tow Dolly Fender - Left Side. FREE Shipping. The Demco Tow-It 2 is where quality and economy meets. Sort By:. Demco. Demco Kar-Kaddy SS KK460SS Operator's Manual. Only 4 left in stock - order soon. 3.2 out of 5 stars 4. Application Equipment Manuals, Harvest Equipment Manuals, Trailer Components Manuals, Rv Towing Manuals, Trailer Manuals, and Request for Archived Manuals are located here. Same day shipping, thousands of accessories and parts reviews.. Drive the front or rear wheels onto the platform and secure the tires with the straps when loading a car on a tow dolly. Get great deals on eBay. There may be additional parts to attach like trailer lights or breaks which may take a little time. The Tow-It 2 is a very economical alternative to the Kar Kaddy 3 and Kar Kaddy SS. Save demco tow dolly to get e-mail alerts and updates on your eBay Feed. 3.6 out of 5 stars 5.. Tow Dolly Safety Guide. PART 5806 04505-95 04176 02214 02163 02164 02580-95 02770 01077 00214 04513 Please order replacement parts by PART NO. Not finding what you're looking for. Name (Example: John S.) Name field cannot be left empty. Contact Email Please enter a valid email address. Submit Thank you!

Your comment has been submitted successfully. Error submitting comment. Please try again momentarily. Product reviews from other F-53 owners. Expert trailers advice with thousands of helpful questions and answers. Guaranteed lowest price and fastest shipping. This galvanized tow dolly features hydraulic disc brakes for safe, controlled stopping and folding ramps for compact storage. Certain vehicles - namely, those with front-wheel-drive automatic transmissions - require either a transmission lube pump system or a driveshaft disconnect when being flat towed. Using a tow dolly eliminates the need for those by lifting your vehicle's front wheels off the road. In addition, using a dolly eliminates the need for base plates that clutter the front of your towed car, difficult-to-install wiring, and a potentially expensive supplemental braking system. Also, if you want to tow multiple vehicles, this dolly is a great alternative to traditional flat towing because you don't have to purchase and install brackets and wiring for all of your cars. Space Saving Kar Kaddy SS The folding design of the Kar Kaddy SS allows you to save space in your garage and at your campsite. This maximizes space around the tow dolly when it's stored and reduces tripping hazards. Hydraulic Disc Brake System The integrated hydraulic braking system features Demco's eZ-Latch surge coupler and disc brakes for safe stopping of your towed vehicle. When the eZ-Latch coupler latch is in the closed position, drop the coupler over the hitch ball and the latch will snap into place. No need to pull the latch up to open the ball socket. The drop that's built into the coupler helps you match your tow vehicle height, and the included breakaway lever activates the tow dolly's brakes should it disconnect from your RV. All hydraulic lines and fittings come pre-installed with the hoses run through the frame.

Disc brakes provide more consistent stopping power and a shorter stopping distance than drum brakes for safer transport of your vehicle. When you apply the brakes in your motorhome, deceleration will occur and momentum will push the dolly toward the rear of your RV. This applies force to the surge coupler's master cylinder, which sends hydraulic fluid through the lines to engage the brakes. This design ensures that the dolly brakes proportionately to your motorhome, which helps to eliminate wear and tear on your RV's brakes. And, because the brakes don't require an electrical signal, an electric brake controller is not needed. Wheeled Tongue Jack The wheeled jack lets you easily move the dolly toward your hitch for coupling and then conveniently swings up and locks into place alongside the trailer tongue for travel. Drop the jack back down and roll the dolly out of the way when you're done towing. Setup and Use The main components of the Kar Kaddy SS come pre-assembled for fast setup. Use the included instructions and hardware to attach the main frame to the tongue assembly, then install the ramps, fenders, mud flaps, and wheels. Finally, connect the pre-routed wiring. Prior to towing, bleed the hydraulic system to remove any air from the brake fluid reservoir. Brake fluid is not included. The textured ramps allow for safe loading of your vehicle onto the integrated wheel platforms. Once your towed car is in place, drape 1 tie-down strap over each front tire. Secure the straps to the platforms, and then use the tie-down winches to easily tighten the straps around the wheels. Attach the included safety chains to your vehicle's frame and you're ready to set out. Included tie-down straps fit most standard automotive tires. Straps for large (DM03528-93) or small (DM03528-81) tires are sold separately. Built for Highway Use Hit the highway in the quality, well-engineered Kar Kaddy SS.

The steerable axle allows the tow dolly to track directly behind your RV, preventing sliding and binding of the tires. The dolly's radial tires create less rolling resistance and heat buildup than bias ply tires, resulting in longer tread life and improved steering at higher speeds. This makes radial tires ideal for highway use. The full LED lighting package is DOT compliant for safe towing. Brake, tail, and turn signal lights, front fender marker lights, and license plate marker lights are included to increase visibility on the road. The galvanized finish resists rust and chipping.This galvanized tow dolly features hydraulic disc brakes for safe, controlled stopping and folding ramps for compact storage.This tow dolly has a pivoting deck for easy maneuvering and electric brakes for safe stopping.This tow dolly has self-steering wheels for superior maneuverability and electric brakes for safe stopping. Adjustable axle positions and sliding ramps fit almost any vehicle. This galvanized tow dolly features hydraulic disc brakes for safe, controlled stopping and folding ramps for compact storage.I like the steering axle. It really helps on tight turns. The assembly went well. I did it alone but a helper would be nice.It is will still have the LED brake, tail and turn signals for your Kar Kaddy SS. The Kar Kaddy 3 tilts down and the Kar Kaddy SS has a ramp so you can simply drive up the dolly and secure your car on it. These dollies also have a. Therefore, you cannot disconnect the towed vehicle from the tow dolly with the tow dolly disconnected from the tow vehicle. That said, this will be the case for most if not all tow dollies. The proper loading and unloading procedures for the Demco Kar Kaddy SS are listed on page 17 of the owner's. Your best bet if you can't use the Kar Kaddy, if you have an RV with a hitch on the back of it, is to flat tow the 2017 Ford Explorer behind that. According to the owner's manual.

The other option is just to remove the shock and make sure it rebounds correctly. With that being said in most cases you won't need one because the dolly is only 615 pounds unloaded which won't likely put enough resistance to engage the brakes. It's not recommend to be backed up anyway and definitely don't back up with the vehicle on the dolly. Since the Kar Kaddy swivels at both the platform and the coupler it'll get pretty squirrely and.Only the manual transmission model can be towed in this manner. This will support the front wheels of your vehicle and leave the rear wheels on the ground for travel. It features a hydraulic. This will be most useful while at the campgrounds where space can be limited. The Kar Kaddy SS also has nicer chrome wheels and a wheeled.The Kar Kaddy SS is the best all in one tow dolly we offer. The Kar Kaddy SS is also made here in. If the toad vehicle's steering wheel does not lock then you will need to find a way to tie this off in a fixed potion, some use the seat belt. That said, I don't have any devices for this but there are some available. If you like you can reference the owner's manual which I have attached for you that further explains the steering wheel lock requirements.The vehicle's rear axle and wheels are very far back, so it isn't going to tilt downwards enough to cause issues over flat pavement, though over speed bumps, if it is raised up enough, it could of course hit the ground, and unfortunately there really isn't any way to overcome that type of obstacle. If you do choose to dolly tow, the best options by far are the. If you are a retired auto mechanic then it will likely be on the lower end as you have experience with this kind of stuff. I have attached the installation details for you to check out. It does come with all of the parts you need (aside from tools) but you will need to purchase brake fluid separately. The tires come mounted on.

Please note, you will need to make the vehicle as light as possible while on the tow dolly as you will likely be very close to the recommended weight capacity. I was able to find that the max width of your 2019 Buick Enclave without factoring the mirrors is 78.8 inches but the tread of the tires is not the widest point of the vehicle. So what you would want to do is use a tape measure to measure the width of the tread on the tires to compare. It should fit on the Roadmaster dolly easily but you should check first.If you find that your Traverse weighs less than 4,800 pounds this will work very well otherwise a heavier-rated unit will need to be obtained locally. The Kar Kaddy features a hydraulic braking system, a foldable ramp.Please note the only Buick Envisions that should be tow dolly towed are the front-wheel-drive vehicles. The All-Wheel-drive vehicles should be towed with all four wheels off the ground on a flat bed trailer. To tow a front-wheel-drive vehicleI took a look at the owners manual for 2009 Kia Sportage and if the vehicle is 4WD it must be towed with all wheels off the ground on a flat bed. The most popular vehicles that are flat towed are Jeep Wrangler models. Most vehicles that.The Sorento must be towed with a dolly whereas the Q3 must be towed on a trailer. I do however recommend that you check each vehicle's owner's manual to be certain. The Kar Kaddy SS is the perfect all in one tow dolly. It has disc. view full answer. Can a Front Wheel Drive Ford EcoSport Be Dolly Towed Yes, you can dolly tow a front wheel drive Ford EcoSport with the front two wheels in the air. The Kar Kaddy SS is the best all in one tow dolly we offer. The towed vehicle however must be licensed as its wheels come into contact with the road. Each state's department of motor vehicles (DMV) addresses tow dolly license requirements therefore this is where you will need to check for exact answers. The Demco Kar Kaddy SS Tow Dolly with Disc.You cannot flat tow the 2.

0L Ecoboost but you can dolly tow it. The manufacturer recommend dolly towing all FWD vehicles and flat towing AWD vehicles but in either case they recommend not exceeding 65 mph. This system uses disc brakes and a surge brake coupler. It does not require adding.In fact, this is the only way the vehicle can be towed behind a motorhome as it cannot be flat-towed with all four wheels down. The steering wheel actually needs to be able to be locked to use this tow dolly so you should not have any concerns here. The Kar Kaddy SS is the perfect all in one.See Driver Mode Control 0 220.It has to be towed on the dolly with front wheel off the ground to avoid damage to the vehicle.The four -wheel drive version cannot be towed at all. You may consider a 2020 Jeep Wrangler or Gladiator instead.I did look up your owners manual at it states that your vehicle is not designed to be towed behind a motorhome so doing so will be at your own risk. Towing with front wheels off the ground is an acceptable way of towing your.Unfortunately, you would not be able to use a tow bar as the front two wheels on your Sportage must be suspended in the air. However, we have a really nice tow dolly, the Demco Kar Kaddy SS Tow Dolly part.However, I recommend you contact the dealer to confirm. The Demco Kar Kaddy SS can be used on a vehicle even if the steering wheel cannot be locked you will just need to securely tie down the front wheels in a straight ahead position. The Kar Kaddy SS is the best all in one tow dolly we offer.Our Lowest Price Pledge ensures you will never overpay for the parts you need. Real product know-how. We make sure that the products we sell are what we say they are, and that they work the way they are supposed to work. Get real advice from a real person who has the knowledge and expertise needed to solve your problem. Most detailed, accurate trailer information available.

Because we take providing accurate product information seriously, we take our own detailed product photos, demo videos and installation videos, as well as verify measurements, instructions, and vehicle fit information. Installations, made easy. We love helping people and have the most highly-trained customer service, hands-on experience, step by step videos and installation instructions. Fast shipping. Your order is automatically routed to get out of our warehouse and to your door as quickly as possible. Personalized service for life. We provide one-on-one, personalized service from the ordering process through the life of your product. Trusted since 1946. We've been serving customers since our parts store first opened in 1946 and continue to be recognized by our customers, our vendors and third parties for exceptional service. Returns Policy Need to return an item? No problem. Please read our Returns Policy for more information. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions. Highly recommended. Dethmers Manufacturing CompanyBEFORE attempting operation.PH: (712) 725-2311 or (712) 725-2302. Toll Free: 1-800-543-3626.Page 1The 1992 and newer Oldsmobile 88 and 98 are in this category, there may be others. In addition to the standard measurement,TI100 - Standard UnitTI110SB - Brake UnitWARNING: Exceeding weight limitations or not using a towing vehicle larger and at least 1,000 lbs. heavierCAUTION: All vehicles to be towed on Demco Tow Dollies must be towed with the front axle on the dolly. Table of Contents. General information. 2. Safety, Signal Words. 3. Equipment Safety Guidelines. 4. Lighting and Marking. 4. Safety Sign Locations. 5. Safety Sign Care. 6. Tire Safety. 6. Remember. 6. Before Operation. 7. During Operation. 7-8. Following Operation. 8. Highway and Transport Operations. 8. Performing Maintenance. 9. Bolt Torque. 10.

Additional Safety Information. 11. Testing Lights. 12. Loading Instructions. 12-14. Damage Prevention. 14. Rear Wheel Drive Precautions. 14. Limited Warranty. 15. Tow Dolly Parts List and Breakdown. 16-17. Assembly Instructions. 18-19. Surge Brake Assembly. 20Actuator Parts List and Breakdown. 21. Optional Kits. 22-23. If you believe that your vehicle has a defectHighway Traffic Safety Administration (NHTSA) inCompany (DEMCO). If NHTSA receives similar complaints, it mayHowever, NHTSAWashington, D.C. 20590. Page 2. To contact NHTSA, you may either call the. Auto Safety Hotline toll-free atWashington, D.C. area) or write to. You can also obtain other information aboutDANGER, WARNING, and CAUTION with theThis signal word is to be limited to the most extremeIt may also be used to alert against unsafe practices. If you have questions not answered in this manual, or require additional copies, please contact yourYou, the operator, can avoidTo avoid personalReplace any caution, warning, danger or instruction safety decal that is not readable or isDo not attempt to operate this Tow It under the influence of alcohol or drugs. Review the safety instructions with all users. Operator should be a responsible adult.Observe all safety signs and practice the instructions on them. Never exceed the limits of a Tow It. If its ability to do a job safely is in questionLight bar kits are available from your dealer or from manufacturer. Page 4Good safetyRed Reflector. Instructions. Winch Operation. Tire Pressure. Page 5How to install safety signs:Whenever possible, trained personnelIf there is anyPage 6Ease into it and become familiarCompletely familiarize yourselfUse an appropriately sized and rated hitch ball andBe sure to check with local law enforcement agencies forTowed vehicles exceeding weight limits willAlways look around to make sureThis is particularly importantPage 7Contact with overhead lines could cause serious injuryDo not exceed 45 M.P.H.

Page 8Always yield to oncoming traffic in all situations, including narrowMake allowances for increased length and weightPoor maintenance is an invitation to trouble.Never operate engine of towing vehicle in a closedWithout immediate medical treatment, serious infection and reactions can occur.Page 9Check tightness of boltsReplace hardware with same grade bolt. NOTE: Unless otherwise specified, high-strength Grade 5 hex bolts are used throughoutTorque SpecificationsTherefore, do not grease or oil bolts orPeriodically check all bolts and nuts to ensure properMake sure all bolts are properly tightened and thoseCheck Lug Nut tension after the first 5 miles andThe ball hitch must latch securely around the ball andRECOMMENDED BALL HEIGHT: 18 inches to the topAn occasional drop of oil may be required on the movingGrease the center pivot pin grease zerk every 1500Grease the main frame platform skids every 1500 miles. These grease zerks are readily accessible from underGrease the Sure LubeTM Hubs every 3,000 miles. Hook the towed vehicle safety chains to the frame of theLeave some slack in the chainUse High Quality Bearing. Grease with Hand Operated. Grease Gun. Check to make sure that all lights are in proper workingExamine the winches and straps, making sure they areBe certain the safety lock pins are locking the strapRetighten straps over the tires after the first 5 miles andEnsure that they are tight. Your Tow-It is equipped with custom made wheelThe TI110 tires must be inflated to the recommended 35NOTE: The winch strap must not be left connected toMake sure the optional light bar is fastened securely atThe wires to the optional light bar should be run along theNOTE: This unit cannot be backed up when loaded. All vehicles mounted on the Tow-It must be mountedRear Wheel Drive: Disconnect the towed vehicleFor manual transmission: Consult your vehicle ownersPage 11You must returnCharge, exchange basis, the proper size strap.

You must return your new unused straps andThank you for Purchasing. Products.Brake lights of tow dolly and towing vehicle should comeLeft turn light of Tow-It and towingShould the turnCheck the plug connectionIf plug connection is incorrect,Step 3. To allow the wheel platform to tilt back for loading:Make sure hitch is locked down and secured with safety clip. Criss-cross safety chains under tongue and secure to towingStep 4. Before loading (and unloading) towed vehicle makeStep 2. Ensure that towed vehicle parking brake is fullyNOTE: Tie downIMPORTANT: Tire tread width or body width of towedStep 7. Place one tie-down strap over each tire and secureStep 5. With someone safely guiding you, slowly drive vehicle onto platform FRONT FORWARD. (Any vehicle mountedMake sure the tire is aligned to ascend onto the ramps. Step 6. Drive vehicle onto platform - Front Forward - untilMake sure theTowed vehicle tires must fit inEngage towedStep 8. Be sure tie-down winch is centered with the tire beforeStep 9. While tightening straps, pull cross strap forward toTighten straps until each tire starts toAfter each strap is tight, insert a safetyStraps must be retightened after first 5 miles of travel. Check straps every 50 miles thereafter to ensure they areRear Wheel Drive: Disconnect towed vehicle driveshaft forFor manual transmission: Consult your vehicle ownersIMPORTANT: Lock the platform in position by pushingPush the handle down as farPage 13Step 10. Make sure the tie-down strap is the correct size forSee page 1 of this instruction for proper fit and exchangeStep 13. To pull the TOW-IT empty, make sure tie-downTiedown winch handles should be left in a down position (horizontal) with safety pins in place when towing loaded or empty. DO. NOT ATTEMPT TO PULL TOW-IT WITH WHEEL PLATFORM IN LOADING (tilted) POSITION.Towing vehicle must be larger and at least 1,000 lbs. heavierDo not pack goods in car that is being towed. Overloading the.

Tow-It or exceeding the width limit may result in damage toDisconnect towed vehicle driveshaft for rear wheel driveSimply placing transmission in neutral is not sufficient to prevent damage toMake sure that platform and vehicle are straight. Reinstall driveshaft. Ensure thatThis will allow the platform to tiltMake sure the winch ratchet handlesPage 14. Examine winches and straps to make sure they are inCheck wheel nuts every trip. Tires must be inflated to recommended pressure by tireBe certain the safety lock pins lock the strap winches. Retighten the straps over the tires after the first 5 milesDEMCO PRODUCTS - TOW-IT Tow DollyYour Demco Tow-It is warranted to be free from defects inThis warranty does not cover:Tires are warranted by the manufacturer against defects inWarrantor has a policy of continuous product improvement. WeTow-It model, including but not limited to state of the art changes,Any part of the Demco Tow-It, except tires and lights, found in theWarrantor assumes no responsibility to the owner for loss of useDethmers Manufacturing Co.P.O. Box 189. Boyden, IA 51234Tire warranty questions andIf your Demco Tow-It develops a defect (except for tires or lights)Until such notice isUpon receipt of notice from you, Warrantor will have a choice ofWarranty claims on tires should be presented to a local authorized dealer of the tire manufacturer. Provide proof of purchaseCoverage under this warranty will be effective only when a copyAll implied warranties, if any, expire and terminate upon expiration of this warranty.

Some states do not allow limitation onWarrantor does not assume responsibility for, nor shall it beSome states do not allow the exclusion or limitation on incidental or consequential damages, so the above exclusion orThe VIN is a 17 digit number located in the lower left corner ofThe label is located on the leftBe sure to include the VIN numberThis warranty gives you specific legal rights, and you may alsoThis is the only express warranty made by Dethmers Manufacturing Co.Warrantor has no liability whatsoever and this warranty is null and voidThis warranty does not cover any tow dolly that has been alteredIn addition, the warranty does not extend to repairs made necessary by normal use of parts, accessories or other equipmentPage 15Right Ratchet Winch Assembly (Plated). Ratchet Frame. Left Spool Tube. Right Spool Tube. Heavy Duty External Snap Ring. Ratchet HandleLeft Ratchet Gear. Right Ratchet Gear. Black Vinyl Hand Grip. Winch Pawl. Winch Pawl Spring SS. Winch Pawl Bushing SS. Left Ratchet Pawl Arm. Right Ratchet Pawl ArmTrunk Connector. Front Half Trailer Wiring Harness. Rear Half Trailer Wiring Harness. Lever Lock Coupler (5,000 lb.). Safety Lock Pin for coupler. Handle. Tongue. Epoxied Bolt. Bracing Strut. Pivot Bushing. Lock Pin (Tongue). Undercarriage (09533-26 for TI110SB). Tilt Bed Ramp. Tinnerman Fender ClampWire Strain Relief. Amber Fender Reflector. White Ground Wire. Back-Up Plate for fender. Red Fender ReflectorRubber Mounting Grommet for light. Sealed Round Tail Light. Upper Half Mainframe. Rear Tire Stop. SureLubeTM Hub and Spindle Assembly. Hook RetainerHub. Grease Seal (NOK AD 2548 E). Inner Cup (L68111). Inner Cone Bearing (L68149). Outer Cup (L44610). Outer Cone Bearing (L44643). Hardened Tongue Washer. Retainer Adjustment Washer for Jam Nut. Sure Lube Dust Cap. Spindle. Please order replacement parts by PART NO.