chevrolet impala 2003 manual

chevrolet impala 2003 manual

This manual includes the latest information at the time it was printed. We reserve the right to make changes after that time without further notice. We use a box and the word CAUTION to tell you about things that could hurt you if you were to ignore the warning. These meal. -.lere is sorr---hin- that c--,- you or other people. A notice will tell you about something that can damage your vehicle. Many times, this damage would not be covered by your warranty, and it could be costly. Six-Way Power Seats Manual Lumbar Heated Seats Reclining Seatbacks Head Restraints Rear Seats Split Folding Rear Seat. Safety Belts. Safety Belts: They Are for Everyone. 1-9 Questions and Answers About Safety Beits How to Wear Safety Belts Properly Driver Position. The sudden movement could startle and confuse you, or make you push a pedal when you don’t want to. Adjust the driver’s seat only when the vehicle is not moving. To adjust the seat do any of the following: Move the seat forward or rearward by sliding the control to the front or the rear. Press LO to warm the seat to a lower temperature. Press HI to warm the seat to a higher temperature. To turn this feature off, move the switch to the center position. Sitting in a reclined position when your vehicle is in motion can be dangerous. Even if you buckle up, your safety belts can’t do their job when you’re reclined like this. The shoulder belt can’t do its job. This position reduces the chance of a neck injury in a crash. Make sure the front seat isn’t reclined. If it is, the rear seatback won’t fold down all the way. To lower the rear seatback, follow these steps: 1. Push and pull the seatback to be sure it is locked in position. 2. Reconnect the center A safety belt that is improperly routed, not properly attached, or twisted won’t provide the protection needed in a crash. It also tells you some things you should not do with safety belts. Don’t let anyone ride where he or she can’t wear a safety belt properly.http://www.bud-drog.pl/userfiles/chaintech-7nif2-manual.xml

• chevrolet impala 2003 manual, chevrolet impala 2003, chevrolet impala 2003 manual, chevrolet impala 2006 manual, chevrolet impala 2003 manual transmission, chevrolet impala 2003 manual download, chevrolet impala 2003 manual for sale, chevrolet impala 2003 manual diagram, chevrolet impala 2003 manual free, chevrolet impala 2003 manual parts, chevrolet impala 2003 manual review, chevrolet impala 2003 manual guide, chevrolet impala 2004 manual, 2003 chevrolet impala manual, 2003 chevrolet impala owners manual pdf, 2003 chevrolet impala repair manual.

See Safety Belt Reminder Light on page 3-31. In most states and in all Canadian provinces, the law says to wear safety belts. Here’s why: They You never know if you’ll be in a crash. The rider Put someone on it.In or the instrument panel.With safety belts, you slow down as the vehicle does.That’s why safety belts make such good sense. Questions and Answers About Safety Belts Won’t I be trapped in the vehicle after an accident if I’m wearing a safety belt? You may be an excellent driver, but if you’re in an accident even one that isn’t your fault your passengers can be hurt. Being a good driver doesn’t protect you from things beyond your control, such as bad drivers. Lap-Shoulder Belt The driver has a lap-shoulder belt. Here’s how to wear it properly. 1. Close and lock the door. 2. Adjust the seat so you can sit up straight. To see how, see “Seats”. The lap part of the belt should be worn low and snug on the hips, just touching the thighs. In a crash, this applies force to the strong pelvic bones. To move it down, squeeze the release lever and the shoulder belt guide as shown and move the height adjuster to the desired position. The shoulder belt is too loose. It won’t give nearly as much protection this way. 1-18 You can be seriol hurt if is too loose. In a crash, you would move forward too much, which could increase injury. The shoulder belt should fit against your body. The belt is buckled in the wrong place. You can be seriously injured if your belt is buckled in the wrong place like this. In a crash, the belt would go up over your abdomen. The belt forces would be there, not at the pelvic bones. The shoulder belt is worn under the arm. It should be worn over the shoulder at all times. 1-20 You can be seriously injured if you wear the shoulder belt under your arm. In a crash, your body would move too far forward, which would increase the chance of head and neck injury. The belt is twisted across the body. You can be seriously injured by a twisted belt.http://behold.lv/allfiles/chaintech-7njl3-manual.xml

In a crash, you wouldn’t have the full width of the belt to spread impact forces. If a belt is twisted, make it straight so it can work properly, or ask your dealer to fix it. The belt should go back out of the way. Before you close the door, be sure the belt is out of the way. If you slam the door on it, you can damage both the belt and your vehicle. When a safety belt is worn properly, it’s more likely that the fetus won’t be hurt in a crash. For pregnant women, as for anyone, the key to making safety belts effective is wearing them properly. To make the belt longer, tilt the latch plate and pull it along the belt. 1-24 To make the belt shorter, pull its free end as shown until the belt is snug. Accident statistics show that unbelted people in the rear seat are hurt more often in crashes than those who are wearing safety belts. Rear passengers who aren’t safety belted can be thrown out of the vehicle in a crash. Don’t let it get twisted. The shoulder belt may lock if you pull the belt across you very quickly. If this happens, let the belt go back slightly to unlock it. Then pull the belt across you more slowly. In a crash, this applies force to the strong pelvic bones.If it doesn’t, you can get it from any GM dealer. Rear shoulder belt comfort guides will provide added safety belt comfort for older children who have outgrown booster seats and for small adults. The elastic 3. Be sure that the belt is not twisted and it lies flat.Then, place the guide The elastic cord must be under the belt and the over the belt, and insert the two edges of the guide on top. Make sure that the shoulder belt crosses the shoulder. To remove and store the comfort guides, squeeze the belt edges together so that you can take them out of the guides. What the proper way to wear safety belts. If possible, an older child should wear a lap-shoulder belt and get the additional restraint a shoulder belt can provide. The belt can’t properly spread the impact forces.

In a crash, the two children can be crushed together and seriously injured. A belt must be used by only one person at a time. 1-32 What if a child is wearing a lap-shoulder belt, but the child is so small that the shoulder belt. If the child wears the belt in CAUTION: (Continued) this way, in a crash the child might slide under the belt. A baby doesn’t weigh much until a crash. During a crash a baby will become so heavy it is not possible to hold it. For example, in a crash at only 25 mph (40 kmlh), a 12-lb. Air bags plus lap-shoulder belts offer outstanding protection for adults and older children, but not for young children and infants. Neither the vehicle’s safety belt system nor its air bag system is designed for them. Add-on child restraints, which are purchased by the vehicle’s owner, are available in four basic types. Selection of a particular restraint should take into consideration not only the child’s weight, height and age but also whether or not the restraint will be compatible with the motor vehicle in which it will be used. A young child’s hip bones are still so small that the vehicle’s regular safety belt may not remain low on the hip bones, as it should. The harness system holds the infant in place and, in a crash, acts to keep the infant positioned in the restraint. 1-38 A forward-facing child seat (C-E) provides restraint for the child’s body with the harness and also sometimes with surfaces such as T-shaped or shelf-like shields. If it is, it will have a label saying that it meets federal motor vehicle safety standards. Then follow the instructions for the restraint. You may find these instructions on the restraint itself or in a booklet, or both. Never secure a child restraint in the center front seat. It’s always better to secure a child restraint in the rear seat. In the United States, some child restraints also have a top strap. If your child restraint has a top strap, it should be anchored.

Anchor the top strap to one of the following anchor points. You’ll find anchors (A) in all three rear seating positions. To assist you in locating the lower anchors for this child restraint system, each seating position with the LATCH system will have a dot on the seatback directly. Never secure a child restraint in the center front seat. It’s always better to secure a child restraint in the rear seat. To tighten the belt, feed the shoulder belt back into the retractor while you push down on the child restraint.The safety belt will move freely again and be ready to work for an adult or larger child passenger. Securing a Child Restraint in the Right Front Seat Position If your child restraint is equipped with the LATCH system, see Lower Anchorages and Top Tethers for. The child restraint instructions will show you how. 4. Buckle the belt. Make sure the release button is positioned so you would be able to unbuckle the safety belt quickly if you ever had to. You may find it helpful to use your knee to push down on the child restraint as you tighten the belt. Your vehicle may also have a side impact air bag for the driver. Wearing your safety belt during a crash helps reduce your chance of hitting things inside the vehicle or being ejected from it. If you’re too close to an inflating air bag, as you would be if you were leaning forward, it could seriously injure you. Safety belts help keep you in position for air bag inflation before and during a crash. The right front passenger’s frontal air bag is in the instrument panel on the passenger’s side.The path of an inflating air bag must be kept clear. Don’t anything between an occupant and an air bag, and don’t attach or put anything on the steering wheel hub or on or near any other air. The driver’s and right front passenger’s frontal air bags are designed to inflate in moderate to severe frontal or near-frontal crashes.

But they are designed to inflate only if the impact speed is above the system’s designed “threshold level”. In an impact of sufficient severity, the air bag sensing system detects that the vehicle is in a crash. For both the frontal and side impact air bags, the sensing system triggers a release of gas from the inflator, which inflates the air bag. After the air bag inflates, it quickly deflates, so quickly that some people may not even realize the air bag inflated. Some components of the air bag module will be hot for a short time. These components include the steering wheel hub for the driver’s frontal air bag and the instrument panel for the right front passenger’s frontal air bag. Additional windshield breakage may also occur from the right front passenger air bag. Air bags are designed to inflate only once. After an air bag inflates, you’ll need some new parts for your air bag system. There are parts of the air bag systems in several places around your vehicle. Your dealer and the service manual have information about servicing your vehicle and the air bag systems. Look for any other loose or damaged safety belt system parts. If you see anything that might keep a safety belt system from doing its job, have it repaired. A damaged restraint system may not properly protect the person using it, resulting in serious injury or even death in a crash. To help make sure your restraint systems are working properly after a crash, have them inspected and any necessary replacements made as soon as possible. Programmable Automatic Door Locks Lockout Protection Leaving Your Vehicle Trunk Windows.A child or others could be badly injured or even killed. They could operate the power windows or other controls or even make the vehicle move. Don’t leave the keys in a vehicle with children. See Roadside Assistance Program on page 7-5 for more information. Notices Your vehicle has a number of features that can help prevent theft. This is normal for any remote keyless entry system.

If the transmitter does not work or if you have to stand closer to your vehicle for the transmitter to work, try this: Check the distance. The ignition must be in OFF or ACC for the remote alarm to work. When you press the remote button, the headlamps will flash, the horn will sound repeatedly and your interior lamps will turn on attracting attention if you need it. The interior lamps will remain on for 40 seconds or until the ignition is turned to ON or LOCK is pressed. You can tell the battery is weak if the transmitter won’t work at the normal range in any location. If you have to get close to your vehicle before the transmitter works, it’s probably time to change the battery. Passengers especially children easily open the doors and fall out of a moving vehicle. When a door is locked, the handle won’t open it. You increase the chance of being thrown out of the vehicle in a crash if the doors aren’t locked. Press the top of the switch to unlock all doors, or press the bottom part of the switch to lock all doors. The rear doors do not have power door lock switches. The lever on each rear door works only that door’s lock. Lockout Protection To protect you from locking your key in the vehicle, this feature stops the power door locks from locking when the keys are in the ignition and a door is open. You can also press the car symbol on your remote keyless entry transmitter, if equipped. Remote Trunk Release You can also unlock the trunk from inside the vehicle. Press the button located below the exterior lamps control on the underside of. Improper use of the emergency trunk release handle could damage it. A child can be overcome by the extreme heat and can suffer permanent injuries or even death from heat stroke. Never leave a child alone in a vehicle, especially with the windows closed in warm or hot weather. See “Retained Accessory Power (RAP)” under Ignition Positions on page 2- 18.

In addition, each passenger’s door has a window switch that controls that door’s window. Press the WINDOW LOCK switch to the right to stop front and rear passengers from using their window switches. The driver can still control all the windows with the lock on. Press the left side of the WINDOW LOCK button to return to normal window operation. Although your vehicle has a number of theft-deterrent features, we know that nothing we put on it can make it impossible to steal. Content Theft-Deterrent Your vehicle may have the optional content theft-deterrent alarm system. See your dealer for service. In an emergency, contact Chevrolet Roadside Assistance. See Roadside Assistance Program on 7-5 fnr mnre infnrmatinn. n9fYp. Don’t make full-throttle starts. With the key in this position, the ignition and automatic transaxle will unlock. ON: This is the position to which the switch returns after you start the engine and release the switch. The switch stays in ON when the engine is running. When the engine starts, let go of the key. The idle speed will go down as your engine warms up. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. When the engine starts, let go of the key. The idle speed will go down as your engine gets warm. Notice: Holding your key in START for longer than 15 seconds at a time will cause your battery to be drained much sooner. You’ll get easier starting and better fuel economy during engine warm-up. Usually, the coolant heater should be plugged in a minimum of four hours prior to starting your vehicle. If you don’t, it could be damaged. How long should you keep the coolant heater plugged in. The answer depends on the outside temperature, the kind of oil you have, and some other things. Maximum engine speed is limited on automatic transaxle vehicles when you’re in PARK (P) or NEUTRAL (N) to protect driveline components from improper operation.

Notice: Shifting to REVERSE (R) while your vehicle moving forward could damage your transaxle. Shift to REVERSE (R) only after your vehicle is stopped. To rock your vehicle back and forth to get out of snow, ice or sand without damaging your transaxle, see If You Are Stuck: In Sand, Mud, Ice or page 4-30. When towing a trailer, so there is less shifting between gears. To set the parking brake, hold the brake pedal down with your right foot. Push down the parking brake pedal with your left foot.You may find it difficult to pull the shift lever out of PARK (P)- This is called “torque To prevent torque lock, set the parking brake and then shift into PARK (P) properly before you leave the. Don’t park over papers: leaves: dry grass or other things that can burn. Engine Exhaust L.gine exhaust can kill. It conta-- carbon monoxide (CO), which you can’t see or smell. But if you ever have to, here are some things to know. Idling the engine with the climate control system off could allow dangerous exhaust into your vehicle. To reduce glare from headlamps behind you, pull the lever at the bottom of the mirror toward you (to the night position). Push the button in the center of the mirror to turn this feature on. The mirror will darken gradually to reduce glare from headlamps behind you. The automatic dimming feature is turned on or pressing the far left button, located on the lower part of the mirror, for up to three seconds. Use the selector switch located above the four-way control panel to choose either the left or right outside mirror. Then press any of the four arrows located on the control pad to move each mirror in the desired direction. It’s a hands-free wireless phone that’s integrated into your vehicle. You can place calls nationwide using voice-activated dialing with no contracts, no roaming charges and no access fees.When programming a garage door, it is advised to park outside of the garage.

It is recommended that a new battery be installed in your hand-held transmitter for quicker and more accurate transmission of the radio frequency. Do not release the button. 2. The indicator light will begin to flash after 20 seconds. To open, lift the latch. Front Storage Area If your vehicle has the split bench front seat, there is an armrest located in the center of the seat. Dual cupholders are located in front of the armrest. It includes a sliding and tilting glass panel and a sunshade. The switch is located on the overhead console if the vehicle is equipped with a Driver Information Center (DIC). If the vehicle is not equipped with a DIC, the sunroof switch is located on the roof panel headliner. Features you can program depend upon the options that came with your vehicle. The following list shows features that can be reset or customized along with the options. Be careful not to reset the OIL LIFE accidentally at any time other than when the oil has been changed. Programmable Modes off. Mode 1: OFF Turns feature Mode 30 SEC 30 seconds. 60 SEC Mode 60 seconds. To determine the mode to which your vehicle is programmed or to program your vehicle to a different mode, do the following: Scroll, using the SEEWPSCAN up or down arrows. A chime will be heard to verify the new setting.A chime will be heard to verify the new setting. If your vehicle has the optional content theft-deterrent system, the first time the remote UNLOCK command is received three flashes will be seen and three chirps will be heard to indicate an alarm condition has occurred. Programmable Modes Mode 1: TRNK OFF Turns feature off. Mode 2: TRNK ON Turns feature on. Before your vehicle was shipped from the factory, it was programmed to Mode 2. If you do not wish to change the current mode, you can either exit the programming mode by following the directions later in this section or program the next feature available on your vehicle. To match the transmitter do the following: 1.

Scroll, using the SEEWPSCAN up or down arrows, until FOB PROG appears 2. Hazard Warning Flashers Other Warning Devices Horn. Tilt Wheel. Turn SignaVMultifunction Lever. Exterior Lamps Interior Lamps. Accessory Power Outlets. Auxiliary Power Connection (Power Drop) Ashtrays and Cigarette Lighter. Climate Controls Dual Climate Control System. Radio with CD Radio with Cassette and CD. Theft-Deterrent Feature (RDS Radios). 3-86 Instrument Panel 3-48 Audio Steering Wheel Controls Understanding Radio Reception 3.51 Care of Your Cassette Tape Player. They also let police know you have a problem. Your front and rear turn signal lamps will flash on and The hazard warning flashers work no matter what position your key is in, and even if the key isn't in. Press the button to make the front and rear turn signal lamps flash on and turn the flashers off. Tilt Wheel A tilt steering wheel allows you to adjust the steering wheel before you drive. You can raise the steering wheel to the highest level to give your legs more room when you exit and enter. These positions allow you to signal a turn or a lane change. To signal a turn, move the lever all the way up or down. When the turn is finished, the lever will return automatically. If you have the headlamps on, they will low-beams when you release the lever. This feature operates even when the headlamps are oft. To spray washer fluid on the windshield, push the paddle. The wipers will run for several sweeps and then either stop or return to your preset speed. This can really help on long trips.The CRUISE light on the instrument panel cluster will come on after the cruise control has been set to the desired speed. 3-1 2 Resuming a Set Speed on the steering wheel Suppose you set your cruise control at a desired speed and release it. Press the SET button on the steering wheel, then release the button and the accelerator pedal. You’ll now cruise at the higher speed.

When going up steep hills, you may have to step on the accelerator pedal to maintain your speed. When going downhill, you may have to brake or shift to a lower gear to keep your speed down. Parking Lamps: Pulling the control out halfway will turn on the parking lamps together with the following: Taillamps License Plate Lamps Instrument Panel Lights Headlamps: Pulling the control all the way out turns on the headlamps together with the previously listed. The feature is activated when the headlamps are on due to the automatic headlamps control feature described previously in this section, and when the ignition is turned off. The control for this feature is located on the exterior lamps control. Your parking lamps must be on for this feature to work. Turn the control clockwise to brighten the lights or counterclockwise to dim them. The ignition must be off for delayed exit lighting to work. When the key is removed, interior illumination will activate and remain on until one of the following occurs: The ignition is moved to ON, the power door locks are activated, or. Console Version shown On vehicles with a center console, it is located at the rear of the console. This feature provides power, ground and accessory wires which can be accessed to add aftermarket electrical equipment to your vehicle. It is located on the passenger’s side of the vehicle, under the glove box, and is labeled with a wire function. The front ashtray may be on the instrument panel or on the console. To remove the instrument panel ashtray, open it, push down on the locking tab and pull out the ashtray. Manual Operation Turn the right knob clockwise or counterclockwise to direct the airflow inside of your vehicle. To change the current mode, select one of the following: (Vent): This mode directs air to the instrument panel outlets. To prevent the air inside of your vehicle from becoming too stale, be sure to return to the outside air mode periodically.

Use the defog mode to clear the windows of fog or moisture and warm the passengers. Use the defrost mode to remove fog or frost from the windshield more quickly. Use of non-GM approved hood deflectors may adversely affect the performance of the system. Keep the path under the front seats clear of objects to help circulate the air inside your vehicle more effectively. It is located underneath the hood just below the windshield wiper arm on the passenger’s side of the vehicle, underneath the air inlet grille. The filter traps most of the pollen from air entering the module. The pictures will help you locate them. Warning lights and gages can signal that something is wrong before it becomes serious enough to cause an expensive repair or replacement. You’ll know how fast you’re going, about how much fuel is in your tank and many other things you need to drive safely and economically. Your odometer shows how far your vehicle has been driven in either miles (used in the United States) or in kilometers (used in Canada). Your vehicle has a tamper-resistant odometer. Notice: Do not operate the engine with the tachometer in the shaded warning area, or engine damage may occur. Safety Belt Reminder Light When the key is turned to ON, a chime will come on for about several seconds to remind people to fasten their safety belts, unless the driver’s safety belt is. The system checks the air bag’s electrical system for malfunctions. The light tells you if there is an electrical problem. The system check includes the air bag sensors, the air bag modules, the wiring and the crash sensing and diagnostic module. If one part isn’t working, the other part can still work and stop you. For good braking, though, you need both parts working well. If the warning light comes on, there is a brake problem. The LOW BRAKE FLUID message in the message center will also appear when there is a brake problem.

If the anti-lock brake system warning light stays on longer than normal after you’ve started your engine, turn the ignition off. This gage shows the engine coolant temperature. It also provides an indicator of how hard your vehicle is working. Dealer or qualified service center diagnosis and service may be required. I d the Light Is Flashing The following may prevent more serious damage to your vehicle: Reducing vehicle speed. If so, be sure to fuel your vehicle with quality fuel. See Gasoline Octane on page 5-5. Poor fuel quality will cause your engine not to run as efficiently as designed. You may notice this as stalling after start-up, stalling when you put the vehicle into gear, misfiring, hesitation on acceleration or stumbling on acceleration. The gage will first indicate empty before you are out of fuel, and you should get more fuel as soon as possible. It gives you important safety and maintenance facts. Service Traction System Warning Message SERVICE TRACTION SYSTEM United If your vehicle is equipped with the traction control system and this message appears when you are driving, there is a problem with your traction control system and your vehicle is in need of service. If the message is displayed when the engine is running, you may have a problem with your charging system. If there is a problem with the charging system, four chimes will sound when the message comes on. A chime will sound continuously, also.It will appear for 60 seconds. After 60 seconds, it will go out. Once the engine oil has been changed, the CHANGE ENGINE OIL message must be reset. If you are in a forward or reverse gear position you will also hear four chimes. Four chimes will also sound. Refer to the fuel gage for a better indication of the amount of fuel remaining in the fuel tank. 3-46 Low Brake Fluid BRAKE. Consult a qualified dealership for necessary repairs to maintain top vehicle performance. It is located in the headliner between the sun visors.

3-48 RESET: You can reset the AVG ECON, FUEL USED or AVG SPEED trip computer modes by pressing and holding this button for three seconds while you are in the mode you wish to reset. Off: No driver information is displayed in this mode of operation. Compassll'emperature Mode: One of eight compass readings and the outside temperature are displayed. A chime will sound to confirm that the new zone number has been set. Automatic Compass Calibration The compass is self-calibrating, which eliminates the need to manually set the compass. When the vehicle is new, the calibration process may not be complete. The information will appear in the following order: AVG ECON (Average Fuel Economy): This shows the average fuel economy since the last reset. INST ECON (Instantaneous Fuel Economy): This shows fuel economy for the most recent second of driving. If you can, it’s very important to do it properly. Added sound equipment may interfere with the operation of your vehicle’s engine, Delphi Electronics radio or other systems, and even damage them. RDS features are available for use only on FM stations that broadcast RDS information. Seek to stations broadcasting the selected type of programming, receive announcements concernina local and national emergencies,. Digital Audio Broadcast transmission services are currently available in Toronto, Montreal, Vancouver, Ottawa, and Windsor. The display will show your selection. The radio will produce one beep. Whenever you press that numbered pushbutton, the station you set will return and the bass and treble equalization that you selected will also be automatically selected for that pushbutton. TYPE and a PTY will appear on the display. 2. Select a category by turning the P-TYPE LIST knob. Press this button to see the message. The message may display the artist and song title, call in phone numbers, etc. If the whole message is not displayed, parts of it will appear every three seconds.